Jump to content
SAU Community

Recommended Posts

Hi all,

Putting the finishing touches on an order for new rims. The supplier has recommended the following.

18x8.5 +32 and 18x9.5 +38

Cars an R33 GTST S1

Can anyone confirm if there will be any issues with this?

Hi all,

Putting the finishing touches on an order for new rims. The supplier has recommended the following.

18x8.5 +32 and 18x9.5 +38

Cars an R33 GTST S1

Can anyone confirm if there will be any issues with this?

they will be fine

Hey All,

Here is my new set up on my new car.

Skyline model = A31 Cefiro

Wheel diameter = 18" Do-Luck Double Six rims :down:

Wheel width = 9.5"

Wheel offset = +15

Tyre size = Front 225/40/18 Rear 235/40/18

Modifications to fit = Flared/lipped guards approx. 20mm front and rear with 3.5 degree's front camber and 3 degree's rear.

Cheers

Phill

Edited by phillb

Skyline model = r32 4 door

Wheel diameter = 17 x 9

Offset = +25

Tyre size = Front 215/45/17 Rear 235/45/17

Modifications to fit = lipped rear, wider front guards... :D

Thinkin bout putting 20mm spacers on the front...could work, might be a little close to guards though?

Tried 25mm ones and are way too close to front bar and guard, looks cool but scared to crack more fibreglass!

will try 20mm ones soon...

Anyone run r33 gtr rims on a 32 with spacers? if so what size spacers on front and rear? Rear would be minimal size im guessing...

Cheers

Joey.

post-25157-1236082649_thumb.jpg

  • 2 weeks later...

Skyline model = 1993 R32 GTR

Wheel diameter = 18" (Work XD9 Rims)

Wheel width = 4 x 10"

Wheel offset = +18

Tyre size = 4 x 275/35/ZR18 Semi Slicks (Not fitted in pics yet)

Modifications to fit = Just One, I lipped the rear arches. Also you need to make sure you buy the work hub rings overwise the wheels will be supported by the studs (not good) instead of the hub (good). My car is lowered so for the first few weeks it slightly rubbed against the front plastic wheel arch guide. No rubbing now.

DSC_0003.jpg

DSC_0001.jpg

Skyline model = 1996 R33 gtst

Wheel diameter = 18" (Work XD9 Rims)

Wheel width = 2 x 9" and 2 x 10"

Wheel offset = +30 and +38 by recommendation, should have got a better offset

Tyre size = 2 x 235/40/18 and 2 x 225/40/18

Modifications to fit = currently fitted with no modifications at all.

Getting 20mm front and rear spacers and guards rolled tomorrow

Edited by blags
  • 2 weeks later...

Skyline model = R32 gtst

Wheel diameter = 17" Buddyclub P1's

Wheel width = 9"

Wheel offset = +17

Tyre size = 215/45/17 front and 235/45/17 rear

Modifications to fit = 2.5 deg camber front 3 deg camber rear (too much havent got rear camber arms yet)

tucked in front lip a little will have to roll rear guards once take camber out but not by much

surprised the fit so well, though they would stick out way further

Skyline Model = 2000 R34 GT-R

Wheel Diameter = 18" (ADVAN Racing RG1)

Wheel Width = 9.5"

Wheel Offset = +12

Tyre Size = 245/40/18 but will replace with 255/40/18 I think.

Modifications to fit = None necessary but car's been lowered via Tanabe Springs 20mm

Tyres are still 7mm within the guards at front

Tyres are still 15mm within the guards at rear

If interested, you can PM me with E-Mail Address for pics

Skyline model = 1996 R33 gtst

Wheel diameter = 18" (Work XD9 Rims)

Wheel width = 2 x 9" and 2 x 10"

Wheel offset = +30 and +38 by recommendation, should have got a better offset

Tyre size = 2 x 235/40/18 and 2 x 225/40/18

Modifications to fit = currently fitted with no modifications at all.

Getting 20mm front and rear spacers and guards rolled tomorrow

thought id finally post a picture, 20mm spacers on rear, nothing on front atm

backgroundedw.jpg

Skyline Model = 1996 R33 GTST

Wheel Diameter = 18" (R34 GTR)

Wheel Width = 9"

Wheel Offset = +30

Tyre Size = 235/40/18

Modifications to fit = None. fronts clear the suspension arms etc by a whisker, no guard issues at all

2vv05qg.jpg

These are Terry's old wheels (see 2 posts above lol). Cheers Terry :)

  • 2 weeks later...
  • 2 weeks later...
^will need to know offsets but since theyre off a r32 gtst it should fit.

any pics of them on the car?

heres the link here for the wheels http://www.skylinesaustralia.com/forums/18...ee-t267980.html

thanks for the help.......

That looks nuts Nisskid. Love it!

I have a 32 GTSt. Guards are rolled and pumped a bit.

I have Advan RS 18x9 +22 with 235/40/18 street tyres. They scrub a little but not too much.

For the track I use R33 GTR wheels (17x9 +30) with 235/45/17 semi's. No scrubbing at all when at the track.

post-10715-1242036471_thumb.jpgpost-10715-1242036518_thumb.jpg

post-10715-1242036394_thumb.jpgpost-10715-1242036436_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...