Jump to content
SAU Community

Recommended Posts

Hey mate, thanks for the reply :)

Finally had a day free yesterday and chucked in the coilovers, nice and low now (although will be lowering fronts a bit more even :P). Yeah I've heard to avoid slip on spacers like the plague, lol.

Cheers for the info, will probably go down this route of just measuring now to figure out spacer size (any suggestions for not-shit-quality brands?). Yeah will probably have to look to getting guards rolled... as well as maybe some camber arms... just lowering it gave it some angle LOL. Now to wait for funds... :P

Most coilovers have around 2 deg camber built in. Nar mate I just got mine from justjap, and they set me back $350 for all round, and they have been fine so far and I drive pretty hard.

Hey guys..

Just been searching through a few pages but yet to come across any confirmation..

Looking to see if the following will fit an R34 GTR,

19 x 10.5 +22

Cheers

Did you ever get a conclusive answer? maybe you just jumped in a bought em?

Hi guys I'm new here just got a r33 s1 sedan and am looking at getting some 17x8 +5 for the fronts and 17x9 +10 rears anyone think these are too aggressive? Thanks in advance.

They will be pretty aggressive but I love the look of them. You will need a roll for sure and some camber to fit them under depending on the tire you want to run.

Have a look a few pages back I think around page 93 there is a photo of Hectics car

Well your rims will stick out about 6mm more

Hey guys just wondering, im about to order a set of Wolf S36's for my 33 gtst, any idea how they would fit if i was to order 18x9.5 +15 all round. im guessing some guard rolling, would there be anything else i have to worry about to get these to fit? Cheers

18x9.5 +15 with a 235/40 18. guard lip rolleds up 100%, camber is set at - .2 with whiteline camber arms, about 3mm off guard, will put camber to -1 before the next track day. front is -2.5 camber, hits guard liner, no big deal

pyiue.jpg

Hey guys I'm trying to get a very flush fitment on my r32 4 door thinking 16x8.5+45 all round with 225/45 rubber anyone got anything similar I was running 17x9+15 all round but they sat a long way out looked awesome but trying for a different look now so want to run the smaller rim my car is as low as I could get my HSD's to go and has rolled guards all round

Any suggestions appreciated

Cheers

Did a search but only found close answers but not exact.

Looking at 19x8.5 +22 up front and 19x9.5 +22 down back. These are going on a r33 GTS-t.

Looking for an aggressive fitment without needing to flare guards so will this size and offset be ok?

Don't want it looking mexican but don't mind if wheels poke out a little bit.

Already have rolled guards and have camber arms.

Cheers.

Hi guys I'm new here just got a r33 s1 sedan and am looking at getting some 17x8 +5 for the fronts and 17x9 +10 rears anyone think these are too aggressive? Thanks in advance.

These would be really agressive, a lot of poke i predict.

May wanna consider a more positive offset to save the hassle of possible defects and that.

If you want aggressive, do it :)

Did a search but only found close answers but not exact.

Looking at 19x8.5 +22 up front and 19x9.5 +22 down back. These are going on a r33 GTS-t.

Looking for an aggressive fitment without needing to flare guards so will this size and offset be ok?

Don't want it looking mexican but don't mind if wheels poke out a little bit.

Already have rolled guards and have camber arms.

Cheers.

I've got 9.5 +23 front and 9.5 +20 rear on a 33 gtst, and don't have that much poke front and rear. Check out the "post your r33" thread if you want to see what that looks like.

Yeah you can, only reason I have bushes was to pull camber out so I could put power down easier, not to do with fitting the wheels

Lowering it on stock arms will give you negative camber, easily enough to tuck in these wheels

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...