Jump to content
SAU Community

Recommended Posts

1 hour ago, niZmO_Man said:

Assuming BNR32, roll the rear guards, roll the front guards. Will most likely rub the plastic inner liner on the front (depending on wheel alignment and height).

I have 275/35 RS-3 on 10" +20 (want to go 285 next time). The front tyres will try to make room :P

So you don't think i'd get away with not rolling the guards at all? Pending which alignment/camber i go? Car won't be too low either about 140mm from the ground

When I had 265 on the wheels, they rubbed on the rear but the front just got away with 'rounded' tyres. But I bought a guard roller and heat gun to roll my self, wasn't hard.

Cambers are (approximately) -1.5° rear and -2.5° front. I think my caster is a bit high (6°-ish), which is probably why it was rubbing on the plastic liner.

DSC_0369.jpg

DSC_0394.jpg

  • Like 2
  • 1 month later...

Hey guess I need some advice , sorry I'm not good with this whole offset thing and I looked at your reference and still don't understand. 

 

I have a 1989 r32 Gtst Sadan 4 door 

will 18x 8.5 offset +43 fit my car or will I need spacer or it just won't fit ?? 

 

Can you guys guys give me advice please . Just before I buy something that won't work 

  • 3 weeks later...
On 19/03/2013 at 11:58 AM, R377 said:

Here is my R33 Skyline GTS-t with 18" Enkei RPF1

Front 18X9.5 + 15. 235 tyre with -3 degrees of camber

Rear 18x10 + 38 (5mm spacer) 265 tyre with -2 degrees of camber.

I could just squeeze my fingernail under the rear guard

post-59293-0-92880900-1363654694_thumb.jpg

post-59293-0-06489100-1363654779_thumb.jpg

post-59293-0-10737700-1363654847_thumb.jpg

post-59293-0-60566500-1363655496_thumb.jpg

post-59293-0-95842000-1363655517_thumb.jpg

 

Not sure if anyone reads this page much these days ?

 

I want to change my wheels on my r33 gts-t above.  You can see at the back with 10+38 (plus a 5mm spacer) with a 265, I still have bit of room to play with using the -2 negative camber.  I would like maximum width at the back - would like a 275 or 285 ideally.  If i go 10.5 at the rear would i need to keep it around +35 to +40 to fit a 275 or 285 tyre  ?

3 hours ago, niZmO_Man said:

Why don't you put 275 or 285 on the 10" wheel?

 

If i keep the wheels i will go 275 or 285, Ive had the wheels a few years now and wanted to get a different wheel so was looking around the 10.5 +40 range.  Not having much luck, most wheel offsets seem to be +22 in the 10.5 which i dont' reckon i would get a 275 or 285 tyre on ? I would have to prob stretch a 245 or something to make it fit...

  • 2 weeks later...

R33 GTR, planning on putting some 18x10.5 +12. Will be lowered, but not much. Used mainly for pleasure, no racing or track. Don't want to roll fenders. Want to put some 285s but I'm not sure if they will rub. 285 30s? 275 35? Any help will be appreciated.

In the same boat, car or situation?, but will have 18x10 +30 te37sl. want a non stretched tyre fitment so assuming 275/35/18 approx. rear guards not rolled fronts are. Scrubbing? Fit without rolling Rear  guards? Thanks for any help !

3 hours ago, GRKGTR said:

So I ended up going TE37 RT 18x10.5 +15 .. Will be running -3.5 Camber at the front and -2.0 / -2.5 at the rear and not modifying the guards (Weekend/track car)

pics when you got em!

  • Like 1
10 hours ago, niZmO_Man said:

I thought my -2.5° up front was heaps lol.

It will be completely functional and not for "stance" crap.. It's more so that I don't want to roll guards, If i can get away with less neg camber then I will.

  • 3 weeks later...

Does anyone know how to measure up guards from the brakes to the lip to work out custom sizes?

Ive got some rocket bunny fenders coming across and im going to fit the to my 32 gtst.  so i cant see what others have got and go from there. the rims im looking at i can choose from anywhere from 18×7.0 to 8×11.5 and offsets avaliable from the high positives to the high negatives.

Is there any how to or what not, to measuring up the guards? 

  • 2 months later...
On ‎2‎/‎05‎/‎2017 at 0:45 PM, Adz2332 said:

Does anyone know how to measure up guards from the brakes to the lip to work out custom sizes?

Ive got some rocket bunny fenders coming across and im going to fit the to my 32 gtst.  so i cant see what others have got and go from there. the rims im looking at i can choose from anywhere from 18×7.0 to 8×11.5 and offsets avaliable from the high positives to the high negatives.

Is there any how to or what not, to measuring up the guards? 

Check with GReddy or whoever you're getting them from, they usually give a guide of what size wheel

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...