Jump to content
SAU Community

Custom Gtr Drag Plenum ** Pics Inside**

JDMfantasy

By JDMfantasy,
in Engines & Forced Induction

 Share

Recommended Posts

JCMarshall_Law Proficient

JCMarshall_Law

Posted
Posted

Looks like a nice job.

Are there flutes on the intake runners (inside the plenum)? Just thought flutes would be a worthwile addition, prolly help smooth the flow into the runners and may help with top end power.

discopotato03 Grand Master

discopotato03

Posted
Posted

If I had the time/resources/interest to develop such a thing it would have two plenums 123-456 fed by two throttle valves . I believe it would stand a much better chance of even distribution over each set of three cylinders and halve the reversion problems . The 153624 order would draw from front back front back etc plenums . Engines such as the four cam twin plenum VG30 do it a bit like that though if memory serves me correctly they have a throttled balance pipe as well . The Porsche flat sixes have had separate plenums from the beginning . Difficult to package on a straight six Skyline but sometimes these things work . Nissan dualled everything else on the RB26 except the plenum and intercooler so who's will be the first ?

Cheers A .

JDMfantasy Explorer

JDMfantasy

Posted
  • Author
Posted

I would not build a manifold based on looks. It is a large capacity plenum with large runners and TB because a ton of air is being moved through it. The runners are 51mm ID, and they taper down to the stock flange (this speeds up air vel.) which will be port matched to the ported head. The opening of each runner is radiused out to from 2" to 3.5" for max flow and smooth transition. This is not going on a street car.

Not sure if you're serious about the welds, but they're all sanded out. None are visible.

Our MA70 supra came with the 7M-GTE 3.0 turbo. We swapped it out in favor of the 1UZ.

r33_racer Grand Master

r33_racer

Posted
Posted

You do realise that sanding welds smooth takes away a good portion of its strength? That material looks about 10-12mm thick in most places, you could have mig welded the whole thing, except where you welded the runners to the flange i guess you prob tig'd them on. or did youz tig the whole thing together??

JDMfantasy Explorer

JDMfantasy

Posted
  • Author
Posted

Tig'd both inside and out. Same material and technique used on our fire truck parts (rated over 500 psi)

You do realise that sanding welds smooth takes away a good portion of its strength?  That material looks about 10-12mm thick in most places, you could have mig welded the whole thing, except where you welded the runners to the flange i guess you prob tig'd them on.  or did youz tig the whole thing together??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 04-LOOX
      R34 GTR Vspec Garage Sale - All must go!

      By 04-LOOX · Posted

      Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...