Jump to content
SAU Community

Recommended Posts

Don't worry about my questions. My bushes are adjustable for camber so i wont need to replace them again. :D

I should be ordering a few things in the next couple of days.

Don't worry about my questions. My bushes are adjustable for camber so i wont need to replace them again.  :unsure:

I should be ordering a few things in the next couple of days.

No problems, ready when you are.

:) cheers :)

No problems, ready when you are.

:D cheers :O

I was actually ready last week and PM'd you about putting in an order, but i guess you didn't get the PM. It looks like im going to end up spending a bit of money this week so i might wait another week or 2 before ordering.

How many sets of shocks are left? Can i put a deposit on a set of shocks?

I was actually ready last week and PM'd you about putting in an order, but i guess you didn't get the PM. It looks like im going to end up spending a bit of money this week so i might wait another week or 2 before ordering.

How many sets of shocks are left? Can i put a deposit on a set of shocks?

Hi, the PM system has been playing up a bit, plus my mailbox was full once last week for a few hours until I cleared some space. I get 30+ PM's as day and I answer every one, so my mailbox fills up pretty quickly.

There are a handfull of sets of R323GTST shocks in stock at Bilstein, so no real panic. If you want to secure a set it is $400 deposit, quite a few guys have done this and then finalisd when they have the budget. PM me for details.

;) cheers :)

Gary, did you get my pm?

I have reponded to all PM that I have received. If you haven't received a reply please PM me again.

:) cheers :D

Hey mate, me again....

Do you have the parts numbers for a set (4) of springs, shocks, bummp stops etc... the stuff i need to get to have a new sprink shock setup....

Also so it will be around 1437 u sed....if so am i able to make a deposit on this and then pay the rest when i get my finances all together....and how long can u leave this deposit down for just in case?!

Cheers DAvid

i would like a price for front and rear set for r32gtst please!
Hey mate, me again....

Do you have the parts numbers for a set (4) of springs, shocks, bummp stops etc... the stuff i need to get to have a new sprink shock setup....

Also so it will be around 1437 u sed....if so am i able to make a deposit on this and then pay the rest when i get my finances all together....and how long can u leave this deposit down for just in case?!

Cheers DAvid

PM's sent

:D cheers :laugh:

Edited by Sydneykid

Hey Sydneykid,

Just had all the suspension gear installed today, and I'm stoked with the result. The ride height is spot on (I used the standard Bilstien circlip setting), now I just have to hope I don't scrape my exhaust of a speedbump or the like...

Thanks again, Ryno

post-3204-1141935137.jpg

Hey Sydneykid,

Just had all the suspension gear installed today, and I'm stoked with the result. The ride height is spot on (I used the standard Bilstien circlip setting), now I just have to hope I don't scrape my exhaust of a speedbump or the like...

Thanks again, Ryno

Hi Ryno,

what is your height from the centre wheel to guard front and rear?

It's about 335mm (though my left front is 342mm for some strange reason).

Mine is on the lower setting of the 2 stock looking ones and its about 330 but my front left is at about 320 for some strange reason. Weird.

Will try to have a look at it this weekend,

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...