Jump to content
SAU Community

Recommended Posts

nfi if mine has hit 6 figures or not.. As it arrived here with 66k... So its hard to tell. But I did my belt and other stuff when I got it.

More for a piece of mind that the car wont break few months down the track... And now 6 months on.. car is going great!

Need more power now! :huh: After seeing so many on the cruise and only hitting 158rwkw...

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611336
Share on other sites

gees though somthing bad happened marss!! lol

mine snapped in the lancer, caused big expensive problems. only got 80k in the line so isnt time to replace just yet

hahahah! ye... bad for my wallet... <_<

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611373
Share on other sites

What timing belt are you replacing it with?

Is there any difference between a Nissan one and an aftermarket one (eg I know GReddy makes them)?

Nah going with the original NISSAN one, i was adviced to KEEP IT REAL... :lol:

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611377
Share on other sites

Nah going with the original NISSAN one, i was adviced to KEEP IT REAL... :lol:

WERD....

I got mine done last week......it was 5K over due...

Bought the car 2 years ago and it had 23k on it....now its got 105k...

I dreaded hitting the 100k mark....but meh its not so bad..... :huh:

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611411
Share on other sites

Mine had 156,000 when I sold it

STD Nissan Timing Belt's fine unless your pushing some rediculous amount of HP.

Gates are good for strength but the blue coating comes off them very quickly. Bit annoying when that's one of the reasons you buy it and show it off..

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611655
Share on other sites

yes i would love to know how aftermarket belts are noiser than nissan ones? this should be a good explanation...

It seems to be the Gates belts rather than all a/m belts in general. More than one workshop has mentioned the fact that the Gates belts tend to be noisy, I can only imagine is related to their design and/or material they are made from.

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611871
Share on other sites

ahh i see, i thought you were being sarcastic!

well there is not a standard belt left on my car. i'm using Greddy timing belt and pitwork accesory belts and they are quiet.

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1611971
Share on other sites

Mine's still running the original belt (well, I assume it is). :cheers: Really gotta do something about that :) *snap* :)

Tossing up whether to do it myself or just get it done by a mechanic. Out of interest, how easy/hard is it to tell if the water pump is cactus or a-ok? I remember SK saying that there is no point just replace the water pump without actually checking it...

Link to comment
https://www.sau.com.au/forums/topic/89259-it-had-to-happen/#findComment-1614044
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...