Jump to content
SAU Community

Recommended Posts

I don't contemplate looking at the same interior again...

yeah, one thing that always turned me off a little if i was to ever get an R33 GTR. I'd just have to look at the same damn interior again and in a way the similarities would still be there. And with so many GTS-T out there "looking" like a GTR these days, from a distance who can tell these days? For that reason I'd probably have to go R32 GTR or something like that. Even if its older, least its not another damn R33 :rofl:

Would I take a GTR over a GTST with $10k thrown at it? Of course.

I'd take the GTS-T that has $10k thrown at it, that you can pick up for $21k.. :D

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

Millions of dollars and probably the same amount of man hours were put into designing and building one of the world’s best high performance cars. I don't think 10k plus a GTS-T, would even come close to a product a well refined as the ‘purposely built’ GTR. Even though I own a GTS-T with mods, driving a GTR is still a great privilege. :D

GTR hands down.

Hard to answer, but i suspect id take the worked GTST.

I have trouble owning std cars, at the very least id have to have wheels, exhaust, filter and clutch, not really stock anymore.

If i could have a RWD GTR (essentially the looks) that had the RB26DETT and weighed the same as the GTST then thats what id want. You can keep the 4wd/4ws etc, just give me a nicely sorted rwd chasis with some good useable power.

So id take MY GTST, its a built engine away from being the perfect car in my eyes. Only the old RB20 wont pack its bags and die :D

A question for GTR owners, how often when at the track or driving like a nutter, does the ATTESA actually kick in? Ive been in a few R33 GTRs and im yet to see the torque gauge flicker, unless they were trying to drift. I think the handling owes more to the susp design then the fact it sometimes is 4wd.

You know, 10K really wouldn't stretch far modding a GTS-T.

-Engine - cams, rebuild (say with good pistons etc), balance etc, theres 2k or so gone already, or more..

-Wheels/tyres - say you got good japanese rims or simmons or something, with quality rubber, theres another 3k

-Clutch, LSD, RB25 box, say goodbye to another 3k or so...

we're up to 8..

You might squeak in some coilovers, and a seat, maybe a steering wheel.

Done your dough and still more to do it properly (don' forget little stuff like bushes, bearings....). No turbo upgrade in that either...

May as well get a GT-R.

Why did I go through the mods as if you were buying a 10k cheaper GTS-T and modding it?

Personally, I wouldn't ever buy a car with "10k" of someone elses mods, in that case I'd have a few k spare to fix their mistakes..

if its a 1989 GTR vs a 1989 GTSt then I'd have to say go the GTR.

If its 1989 GTR vs post 1991 sept GTSt, go the GTSt

If its a post 1991 GTR and a post 1991 sept GTSt, go the GTR.

If its a V Spec 1 or 2, then go the GTR again.

This is based on my experience with reliability, and factory options in these cars.

At the end of the day, it depends if you wanna spend big and save small (GTR) or if you wanna spend small n save big (GTSt). Owning a car is far more than the power it makes or how fun it is to drive. A broken down GTR will cost more to fix than a broken down GTSt. Insurance for a GTR is a good $1000 more than a GTSt if you have a beginner's or bad rating. A GTSt you can take around as a daily driver n not worry bout it taking in too much fuel or attracting the wrong type of attention etc. No point gettin a GTR if its gonna spend its days in your garage locked up.

Personally if I can afford to maintain it for the duration of your purchase, buy a GTR. If you want a zippy Skyline that's fun to drive wth lesser hassles, then buy a GTSt.

If you've never driven a turbo before, buy a GTSt, the last thing we need is another Canadian statistic... which reminds me, you're in Canada, so the parameters that influence your decision is a bit different to those in Australia. However the state of the car and its running costs are still the same.

In fact it might be harder to come by spares in Canada for both RB20DET or RB26DETT cars since they never recieved any cars sporting these engines or drivetrains. R32's were sold locally in Aust and workshops are trained in servicing them. In which case I'd get a GTR, since there's more likely to be more 15 year old R32 GTR's coming into the country soon.

Wow someone revived this thread :birdie: ( :(

As a matter of fact I have never had a turbo car before - actually never had a car with more than 135hp! - so between that, the fact that I might be doing a bit of drifting, and probably not wanting to put a lot of $$$ into the car, and GT-Rs being a bit more expensive than I thought they would be (you guys are driving the prices up - quit it! :D ) - in short, I've decided to go with the GTS-t. And I'll probably not be putting $10k into it after I buy it (yeah I know, famous last words); at the moment, I'm thinking wheels, coilovers, intake, exhaust, FMIC and a tune, so that's about $5k give or take, with some canny shopping possibly needed. Not too bad for something that will be able to embarrass 99% of imports and a high percentage of musclecars as well :P And of course if I get a serious need for speed later I will drop in an RB30DET and blow away everyone :)

Cheers

Jason

You know, 10K really wouldn't stretch far modding a GTS-T.

-Engine - cams, rebuild (say with good pistons etc), balance etc, theres 2k or so gone already, or more..

-Wheels/tyres - say you got good japanese rims or simmons or something, with quality rubber, theres another 3k

-Clutch, LSD, RB25 box, say goodbye to another 3k or so...

we're up to 8..

You might squeak in some coilovers, and a seat, maybe a steering wheel.

Done your dough and still more to do it properly (don' forget little stuff like bushes, bearings....). No turbo upgrade in that either...

Interesting post.

I'm not really sure where you get your prices from, but judging from those prices, I assume you have never actually modified an R32/R33 GTS-t.

"good pistons" alone will cost $2000. Let alone camshafts, and the labour cost involved in an engine rebuild. Try something more like $5-6000 for that in a good reputable workshop with RB engine experience.

"good japanese rims" alone will cost around $3500-$4000 if you imported them yourself and $5000 if you bought them from a local dealer.

"good quality rubber" will set you back $1500-$2000

"clutch, LSD, RB25 box" - $3000 sounds about right if you include labour to fit them all..

Realistically, for $10,000 here's what you'd get:

Air pod: $200

Turbo-back exhaust: $1000 (local custom exhaust)

Bleed Valve: $250 (for a good one)

Suspension: $2500 (Full Whiteline "Works" Kit)

Intercooler & Piping: $1500

Wheels & Tyres: anywhere from $2000 to $5000... Don't expect much change from the latter if you want those Volks or NISMO rims.

MAYBE PowerFC: $1500 (if you buy cheap wheels)

At the end of all that, you'll be putting out about 190-ish rwkw and have a very nicely setup car to drive, but don't expect $10000 to go very far when you're talking about modifying your R32/R33 GTS-t :)

I have trouble owning std cars, at the very least id have to have wheels, exhaust, filter and clutch, not really stock anymore.

A question for GTR owners, how often when at the track or driving like a nutter, does the ATTESA actually kick in? Ive been in a few R33 GTRs and im yet to see the torque gauge flicker, unless they were trying to drift. I think the handling owes more to the susp design then the fact it sometimes is 4wd.

hehehhe...

I agree with not really being able to leave the car stock... So I'd choose the GTR because I know I'd end up modifying it anyway :)

One thing though, I've only taken my GTR out onto the track once with stock suspension and road tyres and it wasn't the best experience... I was so used to high corners speeds of my last car with semi slicks and fully setup coilover suspension, stock suspension and road tyres just didn't cut it :(

But the question I ask you, is how do you know that the drivers of the GTRs you've been in were driving the car properly? I went for a few laps with Andrej Pavicevic in his GTR, and he was using ATESSA coming out of 80% of the corners at Eastern Creek. He also cut a 1:49 in that mostly stock (cam gears, powerfc, boost... stock suspension, road tyres, etc) GTR whilst cruising and chatting to me, so in the right hands, a GTR (even stock) is a fearsome machine.

hehehhe...

I agree with not really being able to leave the car stock... So I'd choose the GTR because I know I'd end up modifying it anyway :)

Be good to be in that position! ... and would love an R32/33 GTR but i cant afford to run a GTR and play with it at the track. Ill never be the fastest car but mine will often be the most enjoyed as it doesnt represent such a large investment of coin and doesnt have the protected species sign around the steering wheel

Fair call about the drivers, but if that GTR doign 1:49s had better rubber, with only a small increase in power, would the ATTESA be workign so hard?

Plus there is that evil voice inside me that likes to scare more recognised performance cars with the poorer cousin. :)

I see your point Merli.. I was only making the point of 10k will go nowhere. But that in mind, pistons don't have to be whiz bang forged ones, decent cast ones could be had a lot cheaper than that, and my estimates were mostly on second hand parts (coilovers, wheels, cams, sprockets, exhaust, seat, box, clutch, etc) and a lot of DIY labour - and even in that case my point is still there, as you say, 10k won;t go far.

Hence what i was saying: the most intelligent way to do it is to get a car for low 20's, with that $10k thrown at it already. Thats if you want a car with a view to modifying it further. Even if you don't like the mods (and if it has been modified from japan generally they do it fairly intelligently anyway), you can take them off and sell them.. only costs a few $hundred at most to change over to what you do want.

By the time you've fitted from scratch an intercooler, EBC, coilovers, bodykit, some decent induction, some nice rims, exhaust, stereo and whatever else ($10k+ anyway) you're probably bored of it already and will want a GTR. With the amount of hours you spend, dealing with workshops, getting it all tuned, ironing out small problems, having it off the road, finding the best deal, researching what you want and whatever else, by then the enthusiasm goes.

In my books, leaving a GTR standard is a little like pulling wings off a fly - cruel and pointless.

As soon as you even remove the boost restrictor - most people just can't help themselves (then zaust, then pods, then boost controller.............). I fall into this catagory of course.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...