Jump to content
SAU Community

Gb: R33 Gts-t And Gtr And R34 Gtt Radiator Guides


Recommended Posts

JimX Funnily enough I have an R33 GTR guide in my office.

I over ordered when somebody cancelled!

I'll take it! How much is it including freight to Sydney? Is it adonized at all? If so what colour? If not, would it be possible to get adonized before sending? If so then at what cost? Have I asked too many questions yet? How about now? Do you hate me yet? How about now?

Sorry, got a little carried away there. PM me your bank details and I'll DD you the cash whether or not it's adonized (although if it's already adonized in hot pink, I may have to re-think the purchase)

  • Replies 520
  • Created
  • Last Reply

Top Posters In This Topic

Jet Dat

Yeah I can make you one, no probs.

thanks heaps mate..i will definately take a r33 GTS-t SII off your hands :wave:

pm me the payment details, i will dd or i can pay on pick up or whatever you like...

is it still possible to get one for a sI r33 bass junky??

ill answer for pete...chances are you'll get 1 mate...as there'll be plenty of them comin back to pete from the guys with series 2's

Hey guys.

Here are the Anoised guides for your viewing pleasure.

I think that next time all guides wil be anodised because the finish is just soooo much better.

BASS OUT

Im lovin the anodised.Got teh hungrys. :D

post-6399-1147743126.jpg

hey bass got it today looks great! one problem... my bonnet wont shut properly. it will lock half way but wont fully push down lock in. ive got a cf bonnet. i cant see anywhere where it is rubbing. anyone had a similar problem?

Freeman.

The reason it wont close is because the CF bonnet will have the tounge that slots into the latch at the bottom attached to the bonnet with a pair of screws that aren't on the normal bonnet. Those two screws are hitting the guide.

Happened when GTTR34 got a CF bonnet. We have to drill two big holes in the guide to make it fit.

Thats what you'll have to do. And by big, I mean hole saw size.

Get a black texta, mark the bottom of the screws, maybe use grease or oil, or vasoline or something. Then lower the bonnet down.

Lift the bonnet, and you'll see where the screws hit the guide.

get masking tape, and cover the section of the guide where the mark is with masking tape (remove the oil or whatever first of course). The tape should be about 100mm square.

Put the oil or grease back on the screws.

Close bonnet.

When you then see the marks on the tape you know where to hole saw.

The masking tape is there so you scratch the guide less.

Get appropriately sized hole saw.

Cut holes.

Reaffix guide.

Bob is your mothers brother.

:)

okay let me write this down.

Wolverine, Dezz, Azn, lordsnipe all need Series II R33 Guides.

Just Boost it wants one of the Series I R33 Guides.

Wolverine and Just Boost It.

You guys are in the same state and I think really close to each other (only 3 postcode numbers apart) so maybe Wolverine you could give yours to Just Boost It?

Who else has series II that I don't know about or havent mentioned??

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
    • Welcome mate. Any pics? Even with a DE I'd be well happy if I had that as a 1st car. 
×
×
  • Create New...