Jump to content
SAU Community

Recommended Posts

Hey guys, just bought myself a 1993 r33 gts-t in what I thought was mint condition. It looked great, sounded sweet with the hegh flow cat and 3" cat back hks exhaust. It wasn't till I got it home that I found out the knob 2 owners ago had overboosted the standard turbo and melted the wheels. I had to pay a bucketload to get new steel wheels, new housing, and wastegate actuator and while I was at it I got it high flowed. Next came the dump pipe. It was at that stage I found a massive power loss at about 4500-6000 rpm. After exhaustive search on the net and lots of trial and error i found out the AFM was shot. Thats getting fixed now and I have run into my next dilemma, WHAT TO WASTE MY MONEY ON NEXT...

I know I need a fmic but need to know what is best and on the cheap having spent way too much already.

Is bar/plate better or tube/fin design. I also want to do the install myself as my mech "friend" has already taken about a month to get everything sorted (In total I have only driven the car for about 2 weeks and am sick of my POS ford laser).

Any suggestions would help.

My mods are:

High flowed steel wheel standard turbo

3" stainless dump pipe

High flow cat

3" HKS cat back exhaust

Turbosmart Boost controller (only running standard boost until afm fixed)

All the rest is standard atm.

Link to comment
https://www.sau.com.au/forums/topic/99114-whats-the-best-cheap-fmic/
Share on other sites

There's nothing wrong with the hybrid copy intercooler. Pick one of those up for approximately $170 delivered to your door step and then take your selection at a piping kit which would cost you a further $350 or so. Either that or look on Ebay for some of the packages they offer

i like these coolers and piping.. there hybird coolers.. custem made pipeing.. give them a call!

http://www.advancedjapautoimports.com.au/intercoolers.html

Edited by DriftSquad

You had the turbo "highflowed", then fitted a decent dump and at that stage this power loss occured between 4500-6000rpm.

How positive are you that the cause is the AFM? Because it sounds like a textbook case of the ecus rich and retard strategy.

Did you try turning the boost down? Did it still happen?

Thanks for the info guys.

I am 100% positive it is the afm cuz the problem disappeared when I borrowed a mates s1 afm.

Boost is currently at standard.

I only noticed this problem after getting the turbo done because it was so badly screwed, especially the wastegate bleeding boost thanks to the busted actuator.

Gtr coolers are ridiculously overpriced for what they are imo. Just like every other gtr part. I mean, sure, it's proven that it's OK.

BUT why buy a gtr cooler for 250-400$ which could be a 15 year old POS when you can buy a 2nd hand apexi cooler with the 90degree return bend for like $350 (I've got one).

be careful, some cheap china kits wont fit in skylines.

I had one which had instructions to bend bits of the chassis to fit the piping. err no lol

I also have heard some horror stories like that. Dodgy kits that dont fit except if you cut and bend things are not my best choice. Heard of some guy who had to cut up his fan to make it fit. Not a good idea. Also is it worth getting a forward facing intake plenum or are they a waste of money?

Hopefully I will finally be getting my baby back today. I miss her so much even though she was almost as slow as my laser (I got beaten by a magna sports!! argh). Have to smoke my mate who owns an 88 supercharged mr2. shouldn't be too hard, hehe.

I would keep an eye out for better quality but second had kits, I got a HKS cooler plus piping for $600. Admittedly that was no cheaper than some of the hybrid copies but I was really patting myself on the back when I was able to fit it in around an hour due to the fact that every part was absouluteley mm perfect

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...