89CAL

Vacuum in the manifold. the pipes have a small amount of pressure in them

Id use aerostart as its designed to go into engines and has anti-knock additives from memory. that's just me but

Spray some aerostart around where you think its leaking will find you the general area where its leaking

There's adjustment as to how far the window goes up. if you pull the door skin you will see the ones im talking about. there at the top of the door and should be slotted holes

Seems way to high. Something is defenatly not right somewhere between the sensor and ecu i know the signal for the speedo splits in two at some point cause the wire was cut to my ecu and my power fc showed 0km/h but my dash speed worked fine, so maybe the water temp does something similar and thats why your gauge works Can you pull the sensor out and stick it in a container of boiling water to see what readings you get? Not sure what amount of coolant will come out or if you have some spare to top it up though

The hardest part of doing the dump is getting the bolts out in one piece. there very prone to snapping. i have CAT high tensile bolts and anti-sieze on mine so it makes it easy as when i want to take the dump off now But that's probably why they were saying the dump pipe was hard. if you snap a bolt in there, there's not alot of room to get it out

So the pfc started showing -30 degrees? What is your voltage in sensor check now?

Is your sensor broken perhaps? Sounds like its not getting voltage through the sensor or it has a short to ground

A normal lsd will turn both wheels the same way with the car off the ground......... a welded diff will just do it around corners as well

intake manifold gasket is a steel gasket from memory (at the head) and a rubber gasket between the runners and top half of the manifold I would buy either or both from Nissan or someone who stocks Nissan genuine parts (eg Just Jap)

have they got different stub axles? thought they were 5 x 1 ?

If there a bit stronger I might get a set of 34 half shafts one day.....

Just bought some Recaro rip off's. should look the goods. So are the 34 shafts thicker then the 33 ones?

Heavy launch, snap

Damn... I was so close lol.... havent had to do it for a while

Speedo could be slightly out Or theres something you can do (cut a wire pretty sure) and it removes the limiter Mine had this wire cut when I got mine, looks like it had been hooked up to an RSM or something cause the tacho wire was cut as well. Or maybe both have to be cut... not sure

are you sure the R33 ones arent the same? I dont remember the spline count but pretty sure it was around 30 I have a RHS drive shaft spare btw, I'm not sure if its the longer or shorter one, just found a photo of the old one and it has LHS written on it and I got sent a RHS one the first time so have a spare New seats might be here tomorrow before I go back out to work with any luck. Or its 7 days out there waiting to see what there like to sit in lol Ordered a cheap HID kit as well..... Must stop spending money..........

Better slip then this happening:

Yeah i think i got a bit mixed up. I was thinking at least one other wheel had to be moving so the abs unit could see that x amount of wheels at y km/h and z amount of wheels at 0km/h and assumes a lookup on the wheels doing 0km/h Then i realised this doesn't work on a 4 wheel lockup as if all the wheels are doing the same speed it doesnt see a problem Oh well lol

It uses one of the coil pack group (of 3) bolts

Need to unplug one of the plugs that goes to the idle control valve then turn the idle screw (in to increase revs from memory) Think its the purple plug you need to unplug. info is here somewhere

No i meant autobarn the franchise...... They always have on the shelf where i live

yeah lol.... I'm pretty sure I have the longer half shaft if you still wanted it. I'm about to go to Brisbane so can sort it out monday when I get back if you want it. Have to double check its the longer one but

for a while..... And I can say its definatly not real, Shiny finish like the copy's. Not rough grey finish like the real ones

I'm not gonna say I stand buy all of the Greddy copys, there are some duds out there, but genuine Greddy's I would 100% trust and a good quality copy as well. Mine was from Autobarn I think (Got it in a trade with someone) and all the surfaces looked pretty nice, as oposed to some which are uneven or weak