Jump to content
SAU Community

Recommended Posts

Is engine oil drain into the sump affected by the pressure within the block?

could putting a external breather on the sump (as i have seen in old holden 5L) to allow it to breath better without having to get to the head and out the head breathers allow for better flow of the oil back into the sump ??

Is engine oil drain into the sump affected by the pressure within the block?

could putting a external breather on the sump (as i have seen in old holden 5L) to allow it to breath better without having to get to the head and out the head breathers allow for better flow of the oil back into the sump ??

Which is what Rob82 has suggested has an influence over how quickly the oil returns to the sump.

Has anybody tryed venting the sump to atmoshpere/catch can to prevent the pressure build up within the crank.

My thoughts are that with sustained high rpm/load the crankcase is pressurising causing the oil not to drain back to the sump. The oil galleries are below the level of oil which means if the sump is pressurised there is no way for oil to drain back. This is why the mod to drain the back of the head via the welch plug on the rear will work as is it more to do with equalling the pressure differential between head and sump than being a drain - but what happens if the oil level is above the level of the rear drain you going to get the same situation.

The way I see it is if the sump itself is vented then you will never have any issue as all the oil drains back from the head will be more than ample to keep the oil in the sump.

It might be an easier option then lifting the head as well if your enigne is back together.

That's a good solution if blow by is a problem. But that's got zero to do with the fact that the head has insufficient oil return capacity for sustained high rpm. Venting the sump does nothing for that problem.

The oil return is best done to the LHS of the sump. Since the crank turns clockwise, that means the oil is returning into the partial vacuum created by the crank rotation. Hence the oil flows intro the sump. Oil level nothwithstanding.

:D cheers :O

ahh found related posts :P

thinking on this, there is only 1 way the block can breath, and thats through these rear oil returns.

isnt there always some level of blow by anyway? whether this results in oil out the breathers or not doesnt remove the pressure being forced up into the head covers to escape.

What about this concept of putting some fuel cell foam in the cam covers somewhere?

Can someone explain it to me? Does it work?

Ps I built my engine before this thread was started and didn't pm SK to ask about oil control. :P

dont worry buddy your not alone, i did the same thing. had my motor running for about 2 months before i knew, now im worried about racing it, so i am gonna pull the motor out this week end.

spewin....

We built my RB30DET back in early 2004 - there was only a few pages of the RB30DET thread at that stage.. So it is a learning curve.. I have allready pulled my engine out and put the tomei restrictor in and it caused my lifter issue.. So it will be interesting to see if you guys get the same issues OR maybe my lifters are nearly dead and yours might be ok.

Sydneykid: QUOTE

Lastly oil pump, if the oil pump is not achieving maximum oil pressure (and therefore flow) by 3,000 rpm, then you have an oil pump problem. Revving the engine to higher rpms should not result in higher oil pressure. If it does, then you have an oil pump problem that needs to be fixed.

----

Can you please give me some ideas on how i can test for this. If i need a new oil pump then i will get one for this weekend and change it while i do my lifters and cams and timing belt....

Thanks

****EDIT UPDATE**** the issue was allways with the bottom end. the restrictor had nothing to do with the lifter noise what so ever. I rebuilt the engine with a totally forged bottem end and used the same lifters and oil restrictor and the engine is fine. no ticking no lifer pump nothing.

SO to confirm with everyone no need to worry - using the 1.5m restrictor and totally blocking off the other oil feed works 100% and was not the cause of my issue. Spun bearings was my issue.

Edited by Guilt-Toy
We built my RB30DET back in early 2004 - there was only a few pages of the RB30DET thread at that stage.. So it is a learning curve.. I have allready pulled my engine out and put the tomei restrictor in and it caused my lifter issue.. So it will be interesting to see if you guys get the same issues OR maybe my lifters are nearly dead and yours might be ok.

A learning curve it was and still is. :dry:

Did you run 2 x 1.5mm Tomei restrictors or just the one?

I believe the RB25's run 1.5mm restrictors from factory?!?

A learning curve it was and still is. :dry:

Did you run 2 x 1.5mm Tomei restrictors or just the one?

I believe the RB25's run 1.5mm restrictors from factory?!?

i'll measure the block i have at home and see.

side note :

nice superman moderator group tag :P

Lastly oil pump, if the oil pump is not achieving maximum oil pressure (and therefore flow) by 3,000 rpm, then you have an oil pump problem. Revving the engine to higher rpms should not result in higher oil pressure. If it does, then you have an oil pump problem that needs to be fixed.

Keep in mind that a swap to solid lifters will also require a swap to camshafts designed to run with solid lifters.

Hope that has been of some help

:dry: cheers :P

If there is the same oil flow/pressure to the head at 3000rpm as there is at 6000rpm then why dont we have oil return issues at crusie on the highway, as 3000 rpm is where most skylines criuse at 110km/hr? Is this a safe assumption?

Just on the SBS... Sump Baffle Syndrome

I dont believe there is an oil surge problem that requires a baffled sump for "most" punters.

Certainly none of the GTR's down here have ever had an issue in the mid 300rwkw range as you know Troy :dry:

I really dont think for a circuit car much more power is required.

Pretty much all of them are using a stock sump overfilled without one dead motor that im aware of, and they are all on semi's.

The other mods to lessen the flow and increase the return are done as they are built motors, and this stops the good ole "SBS" which seems to me, to be caused by everything else discussed here

Being there is enough oil down below all of a sudden, there is no issue.

Call me crazy, call everyone else down here crazy aswell, but no-one has problems.

all you mexicans are crazy :dry: There i said it ok, i said it!

What about on slicks and you've invested alot in your engine and you dont wanna take the risk of spinning something or starving something of oil, then a proper extended baffled sump is a much better option then just overfilling by 1L. Ideally a dry sump setup would be nice. Sooner or later someone only doing the bare minimum will suffer. Depends on how 'built' a motor actually is and how well they've done the required mods to allieviate the oil issues.

Call me crazy, and i dont know about many others racing gtsts or gtrs up here but i dont have any problems at all either. Funnily enough i like having 8-9litres of oil in my engine and sump rather then 4-5l. Helps in other ways rather then just constantly submerging the pickup at anyone time on the track.

P.S incase anyone decides to say it....I like being a bananabender!

Edited by r33_racer

...by all means, its your motor and if im rebuilding it then i would hope to be doing things only once and will be doing what i understand is required. RWD vs AWD sump seems to be a big difference to boot.

I guess im just being a pigeon by coming in here and sh1tting in a great thread :dry: But how much of this is 'critical to an engine" ? I mean if i suppose the restrictors are cheap enough, and the return lines from the back of the head is again cheap enough. But i would hope that will do???

Personally, i was planning on making a proper oil/air seperator and having the return tees to go to drain or return to the engine. Typically i would have it return to the engine, but would like the functionality of running closed to see the amount of oil that is pooling...have even sussed out a relatively compact level switch that i can install in the separator to alarm my data logger when a certain level is reached

^ I think stock oil air separators have a valve so that oil can return to the sump when the engine is turned off.

anyway, on a general note, I haven't had any major oil problems in my rb20 (ie i haven't blown an engine due to oil starvation), though i do get alot of blowby at high rpm. I'm running standard sump, slightly overfilled. However after reading this thread, I'm making these mods to the motor i'm currently building.

how can you tell if you are having oil starvation problems? aside from blowing motors or burning out bearings etc?

There are 2 issues here

1: all the oil goes up to the top of the engine and you get none down the bottom and it causes bottom end engine failure.

2: all the oil goes up to the top and escapes out of the engine and fills your catch can in seconds.

So putting more oil in the engine could cause more oil to escape into the catch can wouldn't it ?

...LOL, by the time you have put a lot of band aids on the engien you could do things properly...but, are certain rocker covers baffled better then others? I see some GTRs with R31 rocker covers, or are they going for the NISMO LM race look? Or is it perhaps that earlier rocker covers are baffled better and stop oil from making its way into the hoses and into the catch can????

...LOL, by the time you have put a lot of band aids on the engien you could do things properly...but, are certain rocker covers baffled better then others? I see some GTRs with R31 rocker covers, or are they going for the NISMO LM race look? Or is it perhaps that earlier rocker covers are baffled better and stop oil from making its way into the hoses and into the catch can????

perhaps the location of the breathers, on hard launches the GTR breathers at the back of the motor assists any oil in the head to exit the breather and enter the catch can.

I like troys idea on making an outside baffle tank that returns the excess oil up top back to the bottom though.

I hate to put restrictors not knowing what they will do in the long run.

Anyway can we all overfill our cars by 1 litre and se if this causes us problem?

This would be a great test. :O

air/oil seperators have been around for ages...old idea, most performance places should know of them or have them available to buy.

Obviously the whole point of doing the oil mods is to solve the problem rather then making a bandaid fix which is what everyone seems to want to do. So far to date no one has had any long term problems with doing the mods, so obviously its not that bad. If it is im sure we will know about it when someone starts experiencing some problems. Weve had ours running in the race car for around 5-6 months so far with no dramas. But im sure time will tell.

Edited by r33_racer

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...