Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

I will only be able to come at about 1pm. can I still enter and call you (james) to be let in? What's the deal for leaving? Can we leave anytime?

Also if we come from the city there is no toll is there...

thanks

Russ

I will only be able to come at about 1pm. can I still enter and call you (james) to be let in? What's the deal for leaving? Can we leave anytime?

Also if we come from the city there is no toll is there...

thanks

Russ

theres always a way around the tolls. depends on which direction u come from. look at www.whereis.com :P

Sorry to burst your bubble guys, but the Show N Shine tomorrow is within a "DRY" zone of the City of Melbourne.

NO alcohol will be permitted.

Its as disappointing for me as it is for you guys, but we must stick to the rules. :)

Official finish is 5.30pm

If you need to leave - just make sure someone is guiding you out (to make sure pedestrians are clear and to remove the bollard). Same with running late - call me (number will be on the bollard) and someone will come to let you in and guide you through.

You need to be 'marshalled' due to safety regulations - again, have to abide by the rules :)

Sorry to burst your bubble guys, but the Show N Shine tomorrow is within a "DRY" zone of the City of Melbourne.

NO alcohol will be permitted.

Its as disappointing for me as it is for you guys, but we must stick to the rules. :D

:O I already have the esky in my car and a slab of carrona's packed. :(

It's not a true SAU event without alcohol :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ok I get you. But isn’t the butterfly intake a headache with the +T?  see this is my plan so far but please advise me into the right direction.  Nistune Ecu, 1000cc Bosch injectors, TD05 or TD06 Kinugawa turbo using stock rb25det exhuast manifold, walbro fuel pump unsure of model I think it’s 450/460, spitfire coils and sparks to suit and a R35 MAF sensor and boost sensor.    I was thinking maybe do a cheap eBay plenum $400-500 or try find a stock det neo intake. I think I’d port match it so it’s getting the full capacity but open to advice please.  Thanks 
    • The issue now is the 'fuel cut' while driving, and when it happend, it does not stall. This, I did not test the fuel pressure while driving as I cannot with a fuel pressure gauge. I do have Nistune logs, yes. I have also replaced the MAF Sensor.   Also related to the FPG Fuel Hanger – I just realized that I need a Deutsch Crimp Tool to crimp some cables for the FPG Fuel Hanger. Need to purchase additional cables as the kit only included 2, which are for the float. FPG has not responded to my emails so far since purchasing. I thought about taking it to someone and having it done professionally, but I am reluctant since everyone I took it to messed up in some way.  
    • There's a good German place in Brisbane if youre up for the drive 😛
    • The German place in Cabramatta was rock solid, fresh pretzel cooked to order back then. Then it went all quiet, after all the poker machines were removed, then I believe it closed for good. I did drive past the other week and noticed outdoor lighting a big screen, but no idea what is there now.  
    • Yeah I suspect even if you hold airmass per cycle/cylinder constant if you get too far away from stock you're still going to have problems running the factory tune within the bounds of the factory load scale. Cams, different displacement/rod ratio, etc. I'm just lucky that the GTIII-SS with wastegate boost + CA compliance cats is pretty much equivalent to stock turbos. When I have actual space I can finally get it tuned and modify the fuel system for flex fuel to 100% handle any detonation concerns when cranking the boost to whatever those dinky turbos can put out.
×
×
  • Create New...