Jump to content
SAU Community

Recommended Posts

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

I will only be able to come at about 1pm. can I still enter and call you (james) to be let in? What's the deal for leaving? Can we leave anytime?

Also if we come from the city there is no toll is there...

thanks

Russ

I will only be able to come at about 1pm. can I still enter and call you (james) to be let in? What's the deal for leaving? Can we leave anytime?

Also if we come from the city there is no toll is there...

thanks

Russ

theres always a way around the tolls. depends on which direction u come from. look at www.whereis.com :P

Sorry to burst your bubble guys, but the Show N Shine tomorrow is within a "DRY" zone of the City of Melbourne.

NO alcohol will be permitted.

Its as disappointing for me as it is for you guys, but we must stick to the rules. :)

Official finish is 5.30pm

If you need to leave - just make sure someone is guiding you out (to make sure pedestrians are clear and to remove the bollard). Same with running late - call me (number will be on the bollard) and someone will come to let you in and guide you through.

You need to be 'marshalled' due to safety regulations - again, have to abide by the rules :)

Sorry to burst your bubble guys, but the Show N Shine tomorrow is within a "DRY" zone of the City of Melbourne.

NO alcohol will be permitted.

Its as disappointing for me as it is for you guys, but we must stick to the rules. :D

:O I already have the esky in my car and a slab of carrona's packed. :(

It's not a true SAU event without alcohol :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...