Jump to content
SAU Community

Recommended Posts

I have to get an EPA noise and emissions test done fairly soon and was wondering If I could get some advice? I have a R33 gtr vspec series 3, current mods are, -5 turbos, power fc, greedy elec boost controller, nismo fuel pump, fuel pressure regulator and injectors, cam gears, exhaust, and pods

I was planning to remove the boost controller, return the injectors and ecu to stock. I believe that the turbos shouldnt be a problem as they are nearly the same as stock. Do I need to return the fuel pump and pressure regulator to stock, I know Im meant to but will they effect emissions if the stock ecu is controlling them and would the inspectors be able to tell between the stock and nismo items. I will quieten the exhaust and leave it that way. Also if I refit the stock ecu will I need to get the car retuned? And is there a difference between an ecu for a gtr and gtr vspec. Any advice is appreciated. Thanks.

Any advice? Just like a bit more of an idea to what stock parts I'll need to start collecting/replacing. Cheers.

Depends if you've been defected or not.

If you have not, you might get away with it.

If you have, unlikely as it'll be listed on the defect. Any legit RWC place should not honour it without an engineers.

not defected.

should i do something to make it not so obvious like weld on both side and paint the new metal plate to make the color same.

thx

Depends if you've been defected or not.

If you have not, you might get away with it.

If you have, unlikely as it'll be listed on the defect. Any legit RWC place should not honour it without an engineers.

You should make it as close to factory as possible mate, closer it is, the better.

Even if it takes more time/money... as once you get defected for it, I'm not sure any engineer in Vic actually signs off on it (if you have airbags)

no airbag, it is a R32, is it going to make my life easier on this? damn stupid previous owner!!! they cut a hole there and not using it

You should make it as close to factory as possible mate, closer it is, the better.

Even if it takes more time/money... as once you get defected for it, I'm not sure any engineer in Vic actually signs off on it (if you have airbags)

No airbag means any engineer will easily sign off on a PROPER repair job should you get defected (requiring engineers)

So you shouldn't have any issues if you do a good repair now, and then just go about your normal life.

Being you'll already have fixed it, no-one will know otherwise :)

I got defected for not having a battery wire with tie downs every 60mm and open ended wheel nuts is that BS or can i be done for this?

i got done for other things but just confused about these

^Wow that's harsh.^

I cleared mine EPA today. Even a standard 32 cat back exhaust was 93 db so it failed yesterday, everything else was ok except the guy thought I had diff fuel pump coz it was noisy. Pulled it out and its nissan :(

Had to get a new muffler and it made it 84 db today. It's been 6 months and I will finally have it back on the road.

I got defected for not having a battery wire with tie downs every 60mm and open ended wheel nuts is that BS or can i be done for this?

i got done for other things but just confused about these

Not sure about the battery wire but my car from factory has open ended wheel nuts as does just about every car I can think of that has steel rims.

Battery wire tie downs every 600mm (60cm). From memory that's the requirement, but sometimes it's better to have every 40cm.

It's a fair call, but pretty pedantic. If I was the copper, I would've said "Fix this and you can go on your way".

As for the open ended wheel nuts.... Not sure!

I got defected for not having a battery wire with tie downs every 60mm and open ended wheel nuts is that BS or can i be done for this?

i got done for other things but just confused about these

I got EPA'd at a defect station at 90.4db...and was told id get a letter warning that it is close to the limit.

I just received a letter saying 94db and to get it checked/fixed.

Im wondering is there any % leeway on these tests like speed cameras have 3km... or is it 90 flat. 90.1 over = defect??

You sure you didn't miss read the reading of 90.4? :blink:

On a serious note, do you have paper work to show 90.4?

Usually they have a tolerance.

I got EPA'd at a defect station at 90.4db...and was told id get a letter warning that it is close to the limit.

I just received a letter saying 94db and to get it checked/fixed.

Im wondering is there any % leeway on these tests like speed cameras have 3km... or is it 90 flat. 90.1 over = defect??

You sure you didn't miss read the reading of 90.4? :blink:

On a serious note, do you have paper work to show 90.4?

^That :)

Either way, you are illegal so what it "is" its honestly irrelevant.

You need to be 89dB 4900RPM if memory serves me correct for the RB25... so regardless of 90.4 or 94.0 - you need to fix your exhaust.

There is no tolerance far as i know however. If it's 0.5dB over, you are over and will fail. As the EPA people "tell" you, thier meters are perfectly calibrated.

I know for a fact they are not (having gone to two testers and had a variance of 2dB), but thats just how it goes really.

You should make it as close to factory as possible mate, closer it is, the better.

Even if it takes more time/money... as once you get defected for it, I'm not sure any engineer in Vic actually signs off on it (if you have airbags)

Even after all the defects i have seen cops hand out, i have yet to see even the best cops give a defect for the battery tray hole.

Edited by Peter89

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...