Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

Hi Guys,

Long time reader first time poster. I have been doing some digging around into acts and legislations. The document that everyone seems to recommed is the EPA 2006 Modification guide which isn't actually a legal document but just a guide.

The Legislation the guide is 'suppose to follow' is the Environment Protection (Vehicle Emissions) Regulations 2003 which can be found here http://www.legislation.vic.gov.au (choose the 'E' and choose Legislation and go down to 60)

the PDF link I have added

http://www.legislation.vic.gov.au/Domino/Web_Notes/LDMS/LTObject_Store/LTObjSt4.nsf/DDE300B846EED9C7CA257616000A3571/AD52E1CA8ECA6916CA2577610035F8CA/$FILE/03-10sr010.pdf

This is what laws EPA Victoria have and what all EPA testers must abide by.

Yes the document has the typical legal layout (which is painful to read) but from reading it and going over it with others. Most of what is in the EPA 2006 Modification guide isn't actually in the legislation it is suppose to follow. Please correct me if I'm wrong but if there is another Act or Legislation I have missed please include it.

There are so many points I can make about who and what has been deemed non-epa compliated but yet is not in there legislation. I know EPA is a VERY touchy issue but I am putting this out there hoping it could make a difference and help inform people what is the law.

Yes I have been playing to much Deus Ex: Human Revolution and think the EPA are evil conspiracists controlled by the Greens which control the Labor Government.

Well the few things i checked.

- Exhaust noise

- Vehicle Emission controls (which covers ECU, PCV etc)

Were the same in the Guidelines, and Stat Rules. And that is what 99% of people here are going to be pinned for ;)

Also the part you have referenced is simply the emissions part for Victoria dont forget. There is more too it like:

Road Safety (Vehicles) Regulations 2009

That one also makes reference to ADR's and other things about emissions etc. I really CBFd trolling through it to see exactly what is referenced but my guess would probably say enough to make it a headache to then go and check each ADR.

  • 1 month later...

Hi Guys,

Just my luck i recieved a Noise Test request from the EPA. Thank god its not a full epa since im running a topmount with the rb30 inside. But i just wanted to be 100% sure, is the simple process of just showing up to a tester, getting it tested then giving the Certificate of Compliance to the EPA? No need to show the car?

Also, should i be worried about chucking the OEM r34 GTT exhaust back on with the amount of modifications i have done to the engine? (eg, gt35r, rb26/30, custom vband dump, ect) no chance of me damading the engine due to back pressure right? Obviously i wont be on WOT but what about the actual test at 4800rpm?

Where are they sending you for the test?

As i have said previously a mates GTR got done for noise, pod filters and a boost controller and the tester said if the car isn't stock its going to the EPA. He wanted stock Nissan cat or an EPA approved import cat with paperwork to prove it complied, stock FPR, stock exhaust, stock FMIC etc

Any "lenient" testers you recommend nismoid?

Although i have to replace my whole exhaust system, i just dont want any further issues with anything else. If thats even possible.

BTW ive been thinking about a racepace exhaust, do you recall what the ball park price they charge?

Been calling them 2 times a day for the last 2-3days but no one ever picks up or even returns my calls =[

No such thing as lenient either it's under or it's not

sorry alex let me be more spesific,

I dont want to draw attention to the fact that im running semi slicks, a top mount turbo ect, A noise tester wouldnt be concerned about this stuff right? Nor should he ask to see the engine?

Sorry mate, just saw your in Melbourne. If you were in Sydney i would say prepare the vaso as regardless of what they catch you for they rape you for everything up here, but Melbourne may be a bit different

Gosh man that must be a nightmare.

When i got home from work and opened up the mailbox to see a envelope from EPA . . . . my heart sunk and i was preparing for the worst. A full engine rip out and buying a new rb25 to put back in. To my relief it was just a noise test. I dont know how much longer i can go driving a car like this lol.

sorry alex let me be more spesific,

I dont want to draw attention to the fact that im running semi slicks, a top mount turbo ect, A noise tester wouldnt be concerned about this stuff right? Nor should he ask to see the engine?

They are testing for noise as i said.

That is all they care about.

go to exhaust city in chelt. great guy for epa noise testing. epa noise testers dont give a shit what your car looks like as long as it pasts test your fine. then you fax it through to epa and your cleared

I had an EPA for noisy exhuast on a VN (had a note through the mail saying the jacks had reported it), I took it to the local RACV place & he failed it so I made some restrictors & went back.

He told me he suspected that restrictors had been installed and threatened to report it to the EPA.

I took it somewhere else & they passed it no probs.

All they do is stick a microphone behind the exhause (they have measuring sticks to make sure it's in the right place), give it a couple of revs and that's it.

As said before, they don't care about anything else on the vehicle, just the noise level, think it's like 90dBA

As for roadies i's getting really hard to get one now because they have to take pictures.

Used to get them all day long up lol

When I bought my R33 they stung me for tint on the door too dark, new windscreen as the one on it was "sandblasted" & front brake discs.

Taking the tint off was fun (not).

  • 1 month later...

I just think its BS how this state/ country doesn't allow you to modify your own vehicle how you want. Not allowed 2 intake mods wtf?? not allowed this not allowed that... what if your car is 10 times safer than standard form then what??

As sad and stupid the laws are im still going ahead with my custom setup. Just puts a downer on it after reading a few posts about it all.

I wish there was good reasons behind not allowing after market modifications. :(

I just think its BS how this state/ country doesn't allow you to modify your own vehicle how you want. Not allowed 2 intake mods wtf?? not allowed this not allowed that... what if your car is 10 times safer than standard form then what??

As sad and stupid the laws are im still going ahead with my custom setup. Just puts a downer on it after reading a few posts about it all.

I wish there was good reasons behind not allowing after market modifications. :(

I think because of the following reasons:

1. Cars have safety features which you can affect by modifying. (Airbags, seatbelts, crumple zones, etc. etc.) Just think about that fully sick 5" monster tacho you see on some dash's. Then picture said tacho hitting the driver in the head when their whole body is flung forward because they rear ended someone.

2. Cars have pollution equipment in place to minimise how much nasty stuff you inhale when your mate drives off. CATs are fitted for a reason. Cars are tuned for pollution minimisation. etc.

3. Modifications done by back yarders can be dangerous as they haven't got full knowledge of engineering principles and the ADR's.

4. Putting modifications to driveline components (such as fully sik 22" chrome bling wheels) means other components wear out faster as increased loads contribute to extra stresses on the system. Again, your average backyarder (and some mechanics for that matter) have no idea when it comes to 'system engineering'. Hence why we have to use an automotive engineer for drastic and not so drastic changes.

I guess to sympathise with you about 2 intake mods.... Agreed, the EPA are a bunch of idiots. They should be educating car enthusiasts on how to get the most performance and fuel economy, but minimal impact on the environment. Don't get me started on Vicroads. Those guys have no idea what so ever. They brought in some rules to say cages weren't allowed to be fitted to cars (at all) because it affected crumple zones etc. Pity that means older cars (say pre 90's) which may not have crumple zones now could not have a cage if you wanted to drive it on the road. Fortunately they have reversed their decision. Twits!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...