Jump to content
SAU Community

Recommended Posts

Business as usual from end of march, its on nengun's site under latest news

Who said anything about them suddenly not being bankrupt??

The reason for the delay at the moment I believe is staff were forced to take leave causing serious production holdups, but those staff will be returning to work shortly so normal production of the currently available stock will resume as normal for the time being.

I'll look for the link but what trident says is correct, the parent company got into finantial problems and it seems production was wound down/halted

/goes googling

googled,

hope you can read Japanese

http://www.apexera.co.jp/pdf/message070209.pdf

Edited by Betz

You're all wrong. It was discovered that the pfc's were infact part of a large scale plan to take over the world. at a later date, all the cars with pfc's would become aware (ie skynet) and would take over the world, one hit and run at a time.

can't you guys read between the lines? :rofl:

I pulled the following from another forum i'm a member of

Hi Guys

With the huge amount of orders we have placed over the last few months we have hit a wall.

Apexi has expressed their apologies on delays and given the following explanation.

QUOTE

At the moment we have stock problems due to the companies current financial situation that you are aware of.

A lot of employee's were forced on leave while this situation was being sorted out with our government and the proposed financial support.

Delays are expected to last until the end of March to very early April and all is expected to be back to normal at the end of April at the latest.

*Edited for better understanding*

You're all wrong. It was discovered that the pfc's were infact part of a large scale plan to take over the world. at a later date, all the cars with pfc's would become aware (ie skynet) and would take over the world, one hit and run at a time.

can't you guys read between the lines? :rofl:

omg it all makes sense now!

TerminatorChip.jpg

it odd, i dont get why they cant adapt the 26 pfc processor onto the rb25 operating board

the 26 pfc works on the rb25 so go figure

its not necessarily economical to do so , they are a large scale business and many production requirements to consider

Jesus, didn't this thread get filled with lots of bullshit quick. I assume everyone knew that Apexi Japan was in financial strife (hence they pulled out of D1) and that they filled for government support to prevent bankruptcy. It would also be safe to assume that they got their support judging by what nengun has posted up regarding Apexi resuming business as usual. Offcourse u won’t find any info on Google regarding this issue, the only one's concerned are Apexi's dealers who have mostly posted info on their sites and the consumers who talk about it on forums

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...