Jump to content
SAU Community

Recommended Posts

There is high temp sheathing that will cover the line you run for the wastegate and from there you can always take the rubber hose (for length) down to your local hydraulic hose guy and get them to make one up. Even if they needs to use a reducign bush for the M5 conneciton

its going to be tight to find something that will fit in there.

I would take out the nipples and braze some brass tube onto them that is about 40mm long and then have a olive/sleeve collet fitting connecting to a braided line. that way you can screw the original fittings in place and leave them in place and screw the lines in situ.

hope this makes sense. just take the gate with the fittings to pirtek/enzed and tell them what you want to do ;) probably cost a bit but it will work and withstand 100's of degrees.

cheers!

Once I get the car back I dont think I will have any choice but take the gate off and see what Enzed and Pirtek can do.

Roy, Yea gate cap is billet.

I spoke to NYTSKY who has the same gate he said he just used normal silicon but I assume his gate is mounted a tad further away from the main heat source.

AD4M, Thanks for that any links to suppliers who stock it?

Quick Update - Found the oil leak.... Appears the oil filter isnt done up quite enough so when the car gets dropped off this arvo I'll fix that up, Then I just have to get a replacement CAS and see if that resolves the problem with it not running.

Cameron.

  • 4 months later...
  • 2 months later...

No real updates, been busy with work and other unexpected things.

I have over christmas installed a new Haltech ECU to replace the Adaptronic, I have just finished wiring up all the sensors etc and all that is remaining is to make a alloy bracket for the map sensor.

I also am trying to find a decent Catch can with -8 / -10 an fittings so I can plum in the breathers.

Once I find a some spare weekends I'll stick it on a trailer and take it to the dyno to start fresh with the tune.

Cheers

Cameron

No real updates, been busy with work and other unexpected things.

I have over christmas installed a new Haltech ECU to replace the Adaptronic, I have just finished wiring up all the sensors etc and all that is remaining is to make a alloy bracket for the map sensor.

I also am trying to find a decent Catch can with -8 / -10 an fittings so I can plum in the breathers.

Once I find a some spare weekends I'll stick it on a trailer and take it to the dyno to start fresh with the tune.

Cheers

Cameron

There is nothing decent readily available on the market, you will need to make one. -10 fittings are the way to go :D

I am looking to make something similar to what RIPS have done for their customers, fitting it where the battery tray is.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...