Jump to content
SAU Community

Recommended Posts

+1

always go to a specialist if you possibly can.

You will always be better off going to a specialist than a mechanic. If there is a price difference it will be negilible and at least you know if there is a problem afterwards they will be able to take care of it themselves, not try and pass the buck on to a parts supplier etc

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

oh and .. if it ( the CV joint ) was on the front ?

if so its about 99% certain you will need to get a wheel alignment

even if it was at the rear I woudl check it out if I were you

eesh.. even THINKING of doing CV joints leave me cold

oh and .. if it ( the CV joint ) was on the front ?

if so its about 99% certain you will need to get a wheel alignment

even if it was at the rear I woudl check it out if I were you

eesh.. even THINKING of doing CV joints leave me cold

yea was front passenger side.

Actually replacing the boot wasn't that bad,

it was cleanin the grease out of my mags that was the most pain.

Yea we got a wheel alignment two days later drives much betta now..

  • 3 months later...

Hi

Sorry to bring up an old topic but i had my CV boot go on the drivers side so i booked it into a CV specialist to have both sides done (boots only as i had the magna done without replacing the joints with no problems 300,000k).

He complained about it being a prick of a job as he needed to take the shafts out (Why i don't know) and after all that only did one so i have to take it back.

Q.

Do the shafts have to be taken out

If so how are they held in.

Thanks

Phil

Hi

Sorry to bring up an old topic but i had my CV boot go on the drivers side so i booked it into a CV specialist to have both sides done (boots only as i had the magna done without replacing the joints with no problems 300,000k).

He complained about it being a prick of a job as he needed to take the shafts out (Why i don't know) and after all that only did one so i have to take it back.

Q.

Do the shafts have to be taken out

If so how are they held in.

Thanks

Phil

i dont know if they need to be removed to do the cv boots but i do know how the shafts come out.

both sides u need to take the top control arm off and steering rack arm and coilover off the strut, then u can lever the hub towards the outside of the car and that will allow enough room to get the spline from out of the brake hub (u gotta undo the big hub bolt first as its holding the shaft in and it will be bloody tight, best bet is a big socket set, i use a 3/4 inch set for this, or get a long breaker bar and it should do the trick).

the drivers side is held into the front diff by just a spline that is a tight fit, u need 2 levers close to the sump/diff and lever the axle out as u pull it outwards and it will pop out.

the passenger side is a flange to flange and 6 bolts need to be removed close to the sump and it will come off easy.

hope it makes sense and gives u an idea of the job

hey guys i have done a few cv,s alot of the time you can just use a stretch fit boot $25 easy as to fit. alot of the time the cv people only do the same as what us mechanics do. but say they serviced the cv. really there is nothing to service on a cv. if it is knocking you buy a replacement end which is held on by a circlip. really there is no diff between a cv specialist and what a mechanic does. as for is it a hard job not really should take no longer then 40 min a side to remove shalft and replace both inner and outer boots and refit .allow will take a bit longer to do at home with no air tools or hoist . well that my 2 cents anyway cheers bernard.

very true bernard, it takes longer to get the shaft out that it does to replace the boots!

unique1 you can also get the front shafts out without removing the upper control arm, steering and shock - you can get enough space by disconnecting the sway bar and the lower control arm ball joint, you can then pull the hub backwards and out pretty easily as it pivots on the steering arm, shock and upper control arm.

very true bernard, it takes longer to get the shaft out that it does to replace the boots!

unique1 you can also get the front shafts out without removing the upper control arm, steering and shock - you can get enough space by disconnecting the sway bar and the lower control arm ball joint, you can then pull the hub backwards and out pretty easily as it pivots on the steering arm, shock and upper control arm.

interesting, thanks Duncan ive had the motor out a good 10 times and removing the front shaft on the drivers side is a pain in the arse and i might try your method next time (if there is a next time, i am hoping not, lol)

Thanks heeps gies >_<

He has replaced the outer boot only on the drivers side as he did not know how to take the shaft out ($90)

Went back today to have the passenger side done he unbolted it at the sump replaced inner and outer ($110)

shame i haden'tgot on here earler i could have given him some information

I think he was confronted with something a bit out of the ordenary and didn't want to damage aney thing

Aneyway a big thanks to all who replied ;)

thanks

Phil

  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...