Jump to content
SAU Community

Recommended Posts

the relay that is connected to the 4WD fuse clicks repeatedly approx every 60secs at idle.

the relay is located near the bonnet hinges on the drivers side ie the black relay.

anyone got ideas on why it is being triggered? can anyone supply circuit diagrams to help out?

ps. the 4WD light is not being lit but does work.

Link to comment
https://www.sau.com.au/forums/topic/176045-4wd-relay-clicking-at-idle/
Share on other sites

the relay that is connected to the 4WD fuse clicks repeatedly approx every 60secs at idle.

the relay is located near the bonnet hinges on the drivers side ie the black relay.

anyone got ideas on why it is being triggered? can anyone supply circuit diagrams to help out?

ps. the 4WD light is not being lit but does work.

Mine does exactly the same thing, have tried to diagnose it, but got nowhere.

Tried tracing things through the diagrams in the service manual, but had no luck.

  • 5 months later...
i still have that infernal clicking.

how is the atessa triggered on stageas? is it a wheel sensor if so could it be faulty or incorrectly located?

The stagea doesn't use wheel sensors, it uses g-force sensors, located under the centre console between the front seats. Maybe if one of the mercury switches was stuffed it could be constantly flicking the relays on/off? This seems uinlikely though, as Jermome would have found out - I have a feeling they would be very expensive to repair, not to mention difficult to source. My money would be on a stuffed relay.

the relay is fine. i have changed it from another S2 that does not have this issue and it still clicks. something is sending a signal to it and it beats me what it is.

perhaps i should take the console out and check the orientation of the g-force sensor??!?! unless someone moved something during the stereo install?

The stagea doesn't use wheel sensors, it uses g-force sensors, located under the centre console between the front seats. Maybe if one of the mercury switches was stuffed it could be constantly flicking the relays on/off? This seems uinlikely though, as Jermome would have found out - I have a feeling they would be very expensive to repair, not to mention difficult to source. My money would be on a stuffed relay.

ATTESA also uses the ABS sensors...as well as g-force sensors.

  • 2 months later...

thanks chook

the powerfc makes it harder to find these codes without swapping ECU's back (i guess).

based on philtacular's issue 'the clicking relay' which showed a pressure switch fault then it is odds on we all have the same issue.

sooo what does the pressure switch do and where is it?

On my R32 GTR the relay in the rear of the boot clicks intermittantly at idle also. My 4WD gauge also goes to full torque split and beyond. As soon as the car moves, it goes back to normal and the clicking stops.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dang I looked at this for so long until I realised it was for the inner rod. I was so confused. This looks like a great tool. Another injected plastic box for my collection. I for one am a torquer. I'm far too anxious and neurotic to not use the correct torques whenever I can. I do honestly feel like my wheels will fall off if I dont.
    • Not sure if you're being serious? I, and all the car people i know, ALWAYS use a torque wrench for wheel nuts. I assumed any car person, apart from tyre centre monkeys with rattle gun in hand, would do it properly.  Anyway, no further reply from me on this unless legit discussion from OP or his query so, over to you, knock yerself out.
    • I was wondering about this. I'll do some research.
    • Why not? Since mines been built, I've used low boost maybe 5 times.
    • Yeah, so widen your search to any Nissan speedo first, then go wider if needed. I will say though, that there is a better than even chance that what I said first will likely come into play. They quite possibly won't come apart without damage. I tried to disassemble a stepper gauge that I wanted to repair. There was no way that needle was coming off the spindle, and I could not see how the spindle would come out of the mechanism behind. Assembled once, never to be disassembled, was my conclusion. Could be the same on the R34 cluster. Failing that - take the cluster to a workshop that specialises in automotive instrument work. There's usually at least one in every Australian city. They'll either be able to do it for you for small cost, or tell you it can't be done. It might be that "it can't be done" unless you follow some arcane procedure, including trickiness to glue it back together or something, that only experienced techs know.
×
×
  • Create New...