Jump to content
SAU Community

Recommended Posts

Hey guys,

When I take off normally on sand Im getting wheelspin, not so much wheelspin but the tyres are skipping over the sand and its starting to get annoying as my estate is filled with it. Would this be the tyres im running? Their brand new ones so dunno. Only running a GTS-t with minor mods as well so probabaly only about 170-180rwkw?

This normal?

PS. Im not riding the clutch, dropping it or whatever :cool:. I have LSD as well but I dont think that would have anything to do with it.

Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/
Share on other sites

haha this threads a joke right?

Sand on the road creates a loose surface...a loose surface is prone to movement. The sand is moving from underneath your tyres, thus your tyres not in direct contact with the road and therefore spinning loosely on top of the road.

Notice the same thing on a wet road? The water acts like a lubricant....

My wheels spin more easily when the rear of the car is jacked up...is that normal?

lol

Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/#findComment-3245094
Share on other sites

Dude put the car into 5th gear and just ride the clutch a bit to take off. Would mostlikely not spin the wheels to easy then.

Or just get outta the car n leave the hand brake off and car in neutral. Give it a push to start it rollin then jump back in the car while its rolling and slip into 2nd and off ya go.

Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/#findComment-3246462
Share on other sites

think he wants everyone to know he got wheelspin :P congrats on getting wheelspin on slippery surface.. *clap clap* dont worry people...his mum says his special..your a SICK C#NT!!

Edited by viet_boi
Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/#findComment-3246617
Share on other sites

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...