Jump to content
SAU Community

Wheels Spinning :(

Dani Boi

By Dani Boi,
in Western Australia

 Share

Recommended Posts

Dani Boi Grand Master

Dani Boi

Posted
Posted

Hey guys,

When I take off normally on sand Im getting wheelspin, not so much wheelspin but the tyres are skipping over the sand and its starting to get annoying as my estate is filled with it. Would this be the tyres im running? Their brand new ones so dunno. Only running a GTS-t with minor mods as well so probabaly only about 170-180rwkw?

This normal?

PS. Im not riding the clutch, dropping it or whatever :cool:. I have LSD as well but I dont think that would have anything to do with it.

Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/
Share on other sites
SLIPPERY Experienced

SLIPPERY

Posted
Posted

haha this threads a joke right?

Sand on the road creates a loose surface...a loose surface is prone to movement. The sand is moving from underneath your tyres, thus your tyres not in direct contact with the road and therefore spinning loosely on top of the road.

Notice the same thing on a wet road? The water acts like a lubricant....

My wheels spin more easily when the rear of the car is jacked up...is that normal?

lol

Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/#findComment-3245094
Share on other sites
jrocket Proficient

jrocket

Posted
Posted

Dude put the car into 5th gear and just ride the clutch a bit to take off. Would mostlikely not spin the wheels to easy then.

Or just get outta the car n leave the hand brake off and car in neutral. Give it a push to start it rollin then jump back in the car while its rolling and slip into 2nd and off ya go.

Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/#findComment-3246462
Share on other sites
viet_boi Mentor

viet_boi

Posted
Posted (edited)

think he wants everyone to know he got wheelspin :P congrats on getting wheelspin on slippery surface.. *clap clap* dont worry people...his mum says his special..your a SICK C#NT!!

Edited by viet_boi
Link to comment
https://www.sau.com.au/forums/topic/177710-wheels-spinning/#findComment-3246617
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
×
×
  • Create New...