Jump to content
SAU Community

Recommended Posts

Okay,

Went in expecting around 180ish rwhp, as my car was misfiring on 7psi..... *sigh*

Pulled 208.8hp@7psi (not bad for stock boost) with a power curve that looks like a set of stairs....

I gots Zorst (w/front pipe), POD, Cold Air, and stock boost...

after having a chat to steve he commented that the timing was retarded a bit, and suggested i advance it a bit for more power... what a difference that made! was able to up the boost to 11psi, no misfiring at all, and the power pulled all the way to redline... DAM.. Kym wants another run!!!!!!

Thanks for the advice steve, i'll be back to tune the new AFC and EBC real soon...

-Kym

edit - Mod :don't forget the no cat kymbo which gives about 10-15 at the rears from the cars i've seen with it and without it.

Link to comment
https://www.sau.com.au/forums/topic/18310-sst-dyno-day-post-your-results-mods/
Share on other sites

  • Replies 83
  • Created
  • Last Reply

Top Posters In This Topic

I hate to steal their thunder.....but :D

There were 2 manual NA RB30's R31's both around 135rwHP

And a very sweet lookin Manual RB20DET GTS-X which put down 137rwHP

I think my wagon was a off the pace due to being auto...manuals were held in 4th, my auto was in 2nd I believe. :O

Originally posted by adam 32

strich9: so your car was misifiring cos the timing was retarded?  

what revs was it misfiring at? (i only ask cos ive got a bit of a flat spot at the moment im trying to sort out)

Yep, Sure was Adam. As soon as I cas-bashed it a bit 2mm (on the cas) advance, all the misfiring stopped except for a small pop ord two between 4-5rpm. Immediately the car pulled like a train and I was able to wind the boost all the way up to 11psi. I HAD to run 7psi before or the misfire was really bad...

It also had MAJOR flat spotting before the timing was corrected.

Attached my dyno sheet :D

dynosst.jpg

343.6 at 1.2 bar on std ceremic terbs with boost control going all over the place. No damage done and boost control now sorted (I wound up the boost and left the duty cycle at a default 60% which is way too high compared to what has been "self learnt" for the lower 1.0 bar boost).

Mods: HKS engine pipe, Jap spec cat, HKS Hiper Zaust, PFC with boost kit. Normal boost 1.0 bar delivered 318 hp atw previously.

Mine managed to get itself to 210.2 HP. Got to 198 with nothing tuned then Steve quickly added fuel to my top end which got me to the 210. Will have to get my S-AFCII tuned properly and wind a bit more boost into her. Might help if i make a partion for my HKS pod, damn that thing's noisy.

For mods, see signature. Note: Nothing tuned yet....

Originally posted by S13_Angel

233.7hp @ 12psi

fmic, pod, 3" zorst (turbo back), badbiki.

very impressive angel, no wonder shes such a sleeper

as for me see the sig its got all the info, theres more roomto play but i don't think it would reliable then

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...