Jump to content
SAU Community

Recommended Posts

This is what a good mate of mine says, (he has one tho)

Hitman said its a must. (He seems to know his stuff, very happy with SAFCII tune he did.)

me confused....

getting walbro as part of this upgrade.

Edited by rio228

well, I run 300rwkw.

Walboro pumps aren't good for that or more, so I dropped the Nismo Fuel pump in (took about 6 minutes) and already have Nismo 555cc injectiors.

Stock FPR is fin up to 370rwkw as R31nismoid said, but if you really must go to another FPR, do it when you're looking for beyond 350rwkw and get a nismo.

If you think you need one for under 350rwkw on any setup, then you're kidding yourself.

Depends on the setup.

The adj fpr is VERY usefull if you have an SAFC and wish to squeeze a little more out of the stock ecu.

I run a nismo fpr as I suspected the std one was playing up + come dyno time if I require a little more out of the injectors its easy enough to do.

Interesting enough the very occasional random lean/surge I was getting has completely disappeared since I fitted the nismo fpr and had it tuned up again.

hey mate, some of these ppl are set in their ways so its a bit hard for a balanced discussion.

i cant talk about sard

but i have a nismo fpr, and it works a treat.

it is definitely a must man, that is an ADJUSTABLE item

its just a piece of mind thing. if my tuner want to increase or decrease pressure, they can

Ok

Im going with the Nismo Reg and the Walbro pump from Slide.

Having the reg as insurance is fine by me.

Injectors would be nice but the $$ are enought as is.

$1250 Power FC

$340ish Pump & Reg

$500 Hitman tune.

$900 Injector is just to much as far as the misses thinks...... :D

Thanks for everyone thoughts.

+1 for the sard fuel reg, bought mine today so i havent got an opinion on its performance just yet. Because my car is in bits at the moment. But i havent heard anything bad about them

it amazes me the amount of people that think you can just install a aftermarket fuel pressure regulator and get instant power increase

Seriously, are people that stupid?

Its a NEED thing. If you need to increase your fuel pressure for some stupid reason, then you get one.

But other than that, you don't need one, and installing one for no reason will make absolutely no difference.

would of thought if you had a 32 and a stock reg possibly 18 years old it would be very cheap insurance to know it is working 100%

just my 2c

an the reason I brought a nismo

however the sard may be a better choice if you plan to run a fuel pressure gauge as it has ports to attach the sensor straight to the reg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...