Jump to content
SAU Community

Hypertune f*kd Up My Car

EMPIRE AERO

By EMPIRE AERO,
in Engines & Forced Induction

 Share

Recommended Posts

EMPIRE AERO Rising Star

EMPIRE AERO

Posted
Posted

well dropped off my car to hypertune for some changes and here r some b4 and after shots!!!

they f*kd it up alright haha im rapped :D its finally done!!

from this

r32gtr_003.jpg

to this!

16102007178.jpg

another pic

16102007179.jpg

gonna see how much power i can make b4 fitting some gas :( should see some track time once my cage gets made and a few other little bits n pieces i have yet to finish on it.

Link to comment
https://www.sau.com.au/forums/topic/189514-hypertune-fkd-up-my-car/
Share on other sites
gt-ahhh! Proficient

gt-ahhh!

Posted
Posted

very nice 26. how much did it set you back? i think everyone wants to see a breakdown of your expenditure! i know i do!

its my goal in life to own a godzilla of similar stature. but id paint it yellow, and replace the wing with an a/m. the stock wing is awful!

EMPIRE AERO Rising Star

EMPIRE AERO

Posted
  • Author
Posted

hahah lets not go into cost, but a minor breakdown, the engine bay still needs a hand polish :D hasnt been done yet

2.7 jun stroker, t88 38gk turbo kit, 19" racing harts, 6" trust cooler thanks to CRD

5 spd ppg synchro box and heaps and heaps of little parts thanks to ian at hi octane

full custom suede interior with bride inserts etc thanks to custom trim works/doran

hypertune did the following for me,

tidy up all engine wiring

plenum, throttle body, intake, water breather setup, catch tank etc etc heaps of fabricating parts!!

i believe its one of the best in aus, may be biased, but thats wat i honestly think!

oh and my carbon bonnet and boot with n1 lip are coming, and n1 3 piece skirts with carbon pods. all on there way

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...