Jump to content
SAU Community

Recommended Posts

  • Replies 121
  • Created
  • Last Reply

Top Posters In This Topic

It would be interesting to know if it were a batch or if slide had some one else do the machine work/balance etc at some point?

R33God, you said the motor had a tapy sound or something.. what's oil pressure like? Drop your oil and look for metallic in it.

If there's a tap/knock coming from the motor it is possible for the motor to drop oil pressure and as a result starve the journal bearing turbo as they require considerably more oil than the BB cores.

im looking at the garrett cartridge replacements from rotor master in campbellfield. they do a similar job to slide but with garrett ball bearing cartridge and a hi flowed exhaust housinhg.

olts straight back on coz it uses ur stock turbo

I am not going to speculate what happened.

BUT

If you are looking for pieces of the turbine or whether "something went through it" i would be looking at the intake to the FMIC or the pipes leading to it. When pieces fly off the front compressor, they will usually get stuck at the fmic, they don't go to the exhaust side :D.

Looks like exactly what happened to my turbo

didnt even last 3months or 5tho kms, electronic boost controller so no overboosting...

NOTHING at all went through the turbo

wasnt even booting it when it went bang and didnt make boost...

im still trying to get a refund..........................................................................

...

post-16112-1195393939_thumb.jpg

post-16112-1195393971_thumb.jpg

One would image that if there loosing blades the wheel is possibly being over sped or surging . I can't say with certainty but many found over the years that compressors with lots of blades like 71mm 8 blade T04's don't like high speed high pressure ratio use .

If in that pic it was a complete blade detached from the compressor then its very likely let go at its root and rubbed on the inside of the housing . I reckon that would do all sorts of nasties balance wise and if it managed to jamb between the wheel and housing that would make itself heard .

Cheers .

Well i got a response from Slide and they basically handballed the problem onto the manufacturer of the turbo for me to sort out....thanks guys!

here is a pic of what became of mine....massive shaft play side to side, nothing in the cooler piping and definitely no overboosting!

oh and I used 8mm speedflow fittings for the oil feed over the recommended drilling of the banjo fitting :S just so there were no excuses

HPIM0033.jpg

Edited by TazzS13
dam...

wonder if I should sell my hi-flow and go something else now...

goodluck mate, the bad rep these turbos are getting i'd be surprised if you got a buyer.

same with me Tazz.... i sent mine to GCG and got a very interesting report...

i think some legal action might be required?

same thing here.

GCG have printed me out a report on the receipt of the turbo i got rebuilt by them.

R33GOD, let me know how far you get with getting your turbo repaired.

yeah mate, click on the link in my sig for all the details.

heres a hint... Murnane Motors were the company who REALLY built these turbos.

Thanks for setting everyone straight as to where the warranty obligations lay. There has been far too much confusion in this thread about this subject.

Good job.

Cheers.

i have had my slide highflow on my car for about 10 000 ks now,no problem yet!!sorry to hear about the problems people are having with these turbos!

my engine needs a rebuild now anyway,will be putting in some good forged pistons and conrods in!will now maybe consider putting a bigger turbo on,will diffnately be garrett!these problems are not good,but some guys have really good luck with highflows,one of the guys in the rb25 power dyno

section got 263kw at the rear wheels with the same turbo i got from slide,the max oversize one,so it seems weird that these problems are happening to these turbos,maybe the rush that they had with orders at the start of this year made the people that do the turbos make mistakes with the rush,but that should not happen!!i was lucky i got my turbo before the rush!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Get something that can spray a bit, something like I'd use is a pressure pack for weed sprayer. I use one with degreaser. Spray it on (make sure you're fully covered up, you don't want that shit on you, especially face/eyes). Alternatively, a paint brush will help here as you can brush and work at the stuff quite aggressively.   Be aware, citric acid can eat metal away and will cause it to rust more later. So make sure you neutralise it when done, and give the fresh metal some protection. That hanger, I'd honestly bin and get something like the Frenchy's drop in replacement. The tank, again, I'd look for something else to replace it with. Remember, as metal turns to rust, it means there's less metal there now. So some patches of your fuel tank are likely to be quite thin.   Personally, Id focus on the front end of things, IE, how did the injectors get clogged if they're meant to be after a fuel filter. Then, once the front is sorted, I'd rig something up, even like a small surge tank, and make sure the engine is now running and all behaving. Then I'd replace the fuel tank and fuel hanger and pump. Also, I'd already be preparing to ditch your fuel filter...  
    • That's looking great! Are you planning to do things like all hidden wiring with it, or you're planning to have it look more like we'd expect an RB in an engine bay to look like?
    • Haha thanks everyone, I'll take everyone's suggestions into consideration. If I do eventually choose a car ill post it here update on the mods I do.
    • I found the ingredients at larger amounts from a Coffee Shop. 1kg Citric Acid for €8.50 500g Baking Soda for €2.50 I tried it out tonight distilled water (I got from my ACs) and dish soap. It does get bubbly with dish soap. In just two hours the hanger has improved significantly and rubbing against any remaining rust seems to flake it off. I'm going to leave it a little bit longer and see how it goes. I have read that someone even used this solution in an ultrasonic cleaner to clean a seized water pump which brought it back to life.
    • If you like more modern stuff than the R series, you should check out a V37 400R, they are pretty mod friendly
×
×
  • Create New...