Jump to content
SAU Community

Recommended Posts

What are your goals? Get stronger? Build lots of muscle or both? Lose fat?

What exercises are you doing to work those muscle groups? What weights, sets and reps?

And perhaps most importantly, are you happy with what you're getting from your current routine?

Happy to recommend a routine for you based on answers to the above, but then you'd be taking a program from someone you haven't seen or know nothing of their ability themselves = no credibility = program could be worse than your existing one.

Don't mean to deter you from posting in the thread, but...

You train calves and abs twice a week, but shoulders, back, chest and legs only once? And you have a whole day devoted to arms?

gooby pls

You'd be suprised how many people train like this.

hazjaz: what do you squat, bench and deadlift for a 1 rep max (or 5 whatever), and what is your bodyweight?

The only time I think it would make sense is if you were a bodybuilder and those particular muscles were your weakness with regard to symmetry and proportion...but even then...

P.S. Think he already said he's 90kg

What are your goals? Get stronger? Build lots of muscle or both? Lose fat?

What exercises are you doing to work those muscle groups? What weights, sets and reps?

And perhaps most importantly, are you happy with what you're getting from your current routine?

Happy to recommend a routine for you based on answers to the above, but then you'd be taking a program from someone you haven't seen or know nothing of their ability themselves = no credibility = program could be worse than your existing one.

My goal previously was to increase strength, in which I did.. I am heading to europe in July so I guess the goal now is to lose fat but dont want to get skinny..

Currently my routine is as follows, although I tend to either add reps if I feel I can/change or add an exercise if I feel like I need to work something more

CHEST

Dips - 4 x failure

Dumbell Flat Bench - 5 x 8-10 (~34kgs)

Dumbell Incline - 4 x 8-10 (~30kgs)

Flat (or decline) Flyes - 4 x 12-15 (16kgs)

Dumbell Pullovers - 3 x 8-10 (30kgs)

Cable Flyes - 3x12-15 (12kgs)

45 degree Calves - 4 x 12-15 (80kgs)

Seated Calves - 4 x 12 (~35kgs)

BACK

Pullups - 4 x failure

T Bar Row - 4 x 8-10 (65kgs)

Lat Pulldown (behind neck) 4 x 10 (~60kgs)

One arm row - 4 x 8-10 (32kgs)

Close Grip Lat Pulldown - 4 x 8-10 (~60kgs)

Lower Back Raise - 3 x 10

Abs

Abs

LEGS

Squats - 6 x 8-15 (start at 60kg and add weight each set)

Leg Press - 4 x 8-10 (160kgs)

Leg Extention - 4 x 8-10 (~60kgs)

Stiff Leg Deadlift - 4 x 8-10 (35kg each side.. doesn't feel right to go too heavy with this..)

45 degree Calves - 4 x 12-15 (80kgs)

Seated Calves - 4 x 12 (~35kgs)

SHOULDERS

Standing Barbell Press - 5 x 8-10 (~45kg)

Seated Dumbell Press - 4 x 8-10 (26kgs)

Side Lat Raise - 3 x 8-10 (12kg)

Barbell Front Raise - 3 x 8-10 (35kg)

- Super Set Seated Dumbbell Rear Delt Row - 3 x 8-10 (22kg)

Barbell Shrugs 4 x 6-12 (40kgs)

ARMS

Barbell Curls - 5 x 8-10 (40kg)

Preacher Curls - 4 x 8-10 (35kg)

Concentration Curls - 4 x 8-10 (12kg)

Skull Crush - 5 x 8-10 (30kg)

Cable Overhead Extention - 4 x 8-10

Rope Extention - 3 x 10

I try to get cardio in on the off days.. really depends on work though haha, I am interested to hear what you think of this..

You'd be suprised how many people train like this.

hazjaz: what do you squat, bench and deadlift for a 1 rep max (or 5 whatever), and what is your bodyweight?

I have never attempted 1 lift for a squat.. Deadlift probably 160-170kg for a couple reps, never had a strong chest but bench I have done around 100-110kgs

Splitting the body part up into groups (such as chest, back, arms) works great if you're on the juice. From the best of my knowledge and a ton of anecdotal evidence, for natural guys, hitting the same muscle group more than once a week seems to give the best results in terms of "rep range strength" and muscle mass increases.

This obviously means your volume will have to reduce, but if you work it right, you'll increase your intensity to take advantage of the increased frequency.

It's been suggested (and this is further backed up by some studies, and lots of "real world" evidence) that hypertrophy and CNS stimulation only requires a certain amount of stimuli, to produce a certain amount of gainz brah. After that threshold has been reached, you're only tearing down muscle fibre and depleting stored muscle glycogen for no reason other than to feel "the burn", etc. (just to illustrate a point)

Example. For your body to produce 20 grams of new muscle tissue in your chest, it requires only 3 sets (of a high enough intensity). Regardless of how many sets you do, your body can only produce a certain amount of new muscle tissue. Just because you did 6 sets, doesn't mean you'll grow 40 grams. Just because you did 9 sets, doesn't mean you'll grow 60 grams. See where I'm going with this?

'I really only want to gain strength, I'm not so concerned about size.' Yeah, well, the beauty about strength is that an increase in muscle cross sectional area can have a pretty profound effect on strength. You say you want to lose a bit of fat without looking skinny...

I'd say find a program where you train each muscle group at least twice a week, with a lower individual daily volume, but the same/if not higher total weekly/monthly volume. Throw in some fasted cardio (conflicting evidence about whether or not it's more/less effective, but it doesn't hurt) on the off days, a tiny bit of carb cycling, and you'll be home and hosed.

I'd recommend doing a google search on "DC Training"... they say it's for advanced dudes only (+3 years of heavy lifting) and juiced up bro's, but if you look at it closely, it actually resembles what a natural lifter requires really... really... really well.

Unless of course you're on the juice.

In which case, I'd still do DC Training. And up your Tren dosage to 500mg/week ;)

Hahaha.. awesome. Nah, but seriously, have a google of that DC Training and see what you think. I'm sure the other guys/gals here will also have some decent recommendations for you.

Thought I'd join in on this thread..

Currently 90kgs and the goal is to gain muscle, before going onto a strict diet/new training program.

I have just switched up my routine and train;

Chest Calves

Back Abs

Legs Calves

Shoulders Abs

Arms

Bit of a struggle to push out consistent weight and reps as it depends on how big of a day at work I have had.. I aim for 5 sets of the main muscle of that day/what I think needs it the most and work my way from there.

I have come across Evogen Stack which I want to give a try.. it includes a pre/intra/post. One of the supps in a carb loader.. does anyone have experience with this?

And does anyone have some feedback for Cellucor products?

Anyway, thats me for now

Welcome.

You'll find most in here subscribe to strength/power lifting and less body building type routines.

Also don't listen to anything Birds has to say, he's a raging homo and needs to eat a hamburger ;)

As a semi reformed bro curler and squat dodger I can relate to some of your routine - I used to do 3 different bicep exercises 3 times a week - I can say that since shift to more of a compound exercise routine I am a bit more rounded strength wise and enjoy the work more. I also got bigger and easier but that was more to do with weight/rep scheme.

If your goal is trimming/fat lose, then a big part of that will be in your diet. Aiming for sets of 8-12 and having shorter breaks will assist also, that's just what I find though, everyone is different.

Edited by ActionDan

DC is kind of advanced for where he's at, i'd suggest PTC Beginner routine -

3x10 squat

3x8 Bench, OHP, bent over row, Stiff leg Deadlift, barbell curl (I did Romanian for mine because the definitions vary)

do this 3 times a week and do some sprints/hill/stair runs if you like. Add 2.5kg per workout or per week depending on how fast you progress. Do this for a few months and see how you go.

Possibly the easiest to remember and follow beginner strength routine. Of course you can always do Starting Strength or 5/3/1 for beginners, but they have a bit more thought involved.

Diet is also important, .8-1g/kg bodyweight per day is a good starting guide for most. As for more specific dieting advice, well that's a controversy all of it's own.

My goal previously was to increase strength, in which I did.. I am heading to europe in July so I guess the goal now is to lose fat but dont want to get skinny..

Currently my routine is as follows, although I tend to either add reps if I feel I can/change or add an exercise if I feel like I need to work something more

CHEST

Dips - 4 x failure

Dumbell Flat Bench - 5 x 8-10 (~34kgs)

Dumbell Incline - 4 x 8-10 (~30kgs)

Flat (or decline) Flyes - 4 x 12-15 (16kgs)

Dumbell Pullovers - 3 x 8-10 (30kgs)

Cable Flyes - 3x12-15 (12kgs)

45 degree Calves - 4 x 12-15 (80kgs)

Seated Calves - 4 x 12 (~35kgs)

BACK

Pullups - 4 x failure

T Bar Row - 4 x 8-10 (65kgs)

Lat Pulldown (behind neck) 4 x 10 (~60kgs)

One arm row - 4 x 8-10 (32kgs)

Close Grip Lat Pulldown - 4 x 8-10 (~60kgs)

Lower Back Raise - 3 x 10

Abs

Abs

LEGS

Squats - 6 x 8-15 (start at 60kg and add weight each set)

Leg Press - 4 x 8-10 (160kgs)

Leg Extention - 4 x 8-10 (~60kgs)

Stiff Leg Deadlift - 4 x 8-10 (35kg each side.. doesn't feel right to go too heavy with this..)

45 degree Calves - 4 x 12-15 (80kgs)

Seated Calves - 4 x 12 (~35kgs)

SHOULDERS

Standing Barbell Press - 5 x 8-10 (~45kg)

Seated Dumbell Press - 4 x 8-10 (26kgs)

Side Lat Raise - 3 x 8-10 (12kg)

Barbell Front Raise - 3 x 8-10 (35kg)

- Super Set Seated Dumbbell Rear Delt Row - 3 x 8-10 (22kg)

Barbell Shrugs 4 x 6-12 (40kgs)

ARMS

Barbell Curls - 5 x 8-10 (40kg)

Preacher Curls - 4 x 8-10 (35kg)

Concentration Curls - 4 x 8-10 (12kg)

Skull Crush - 5 x 8-10 (30kg)

Cable Overhead Extention - 4 x 8-10

Rope Extention - 3 x 10

I try to get cardio in on the off days.. really depends on work though haha, I am interested to hear what you think of this..

For most part I agree with what Dajae said. Where I really agree is that training one group of muscles once a week is not enough for someone trying to build up the basics - be it solid strength foundations or a lot of muscle mass, or both (they are very much correlated, so strength goals can be a great thing for building the latter). Very few can benefit from the kind of training you're engaging in and, like I said before, the only people I've seen do that kind of routine with success are body builders who are...usually on juice...and far past the stages of building basic/foundation strength/muscle. I say basic because unless I see a picture to the contrary, showing you with decent muscle mass, then all I have to go off here are your weights that you lift and judging by those, you still have a way to go before it is worth your while looking at advanced routines...even if you've been training for years.

My own opinion is that you're doing way too much exercise and the exercise you're doing isn't as effectively arranged as it could be. I think you're focusing on isolation movements that are of little benefit to you right now; I think you're looking at supplements way before you even need them, to use as bandaid fixes / plateau breakers when there are fundamental issues with your exercise routine. Without this being a pissing contest, you go to the gym 5 days a week and spend about an hour a session there (judging by your exercises) doing 11ty different exercises. I go 4 days a week, spend 40 minutes there, am 12kg lighter and lifting heavier than you - from doing only 4 different exercises. The only supplement I use is protein. I'm not naturally strong, quite the opposite...but where I succeed is working out smarter rather than harder; I recognise the importance of adequate rest and a diet that supports a training routine that doesn't leave my muscles beyond repair for days, that is focused on improving strength where I can. And I'm not even what I would consider a great lifter!

I used to have a lot of exercises like you and spent a lot of time in the gym thinking more is better. I think that when we see progress from exercises we don't like to give them up, so as we discover new exercises we want to adopt, we end up hoarding exercises and our routine turns into a mess of low intensity overtraining without adequate rest periods for muscle growth/repair. We feel we're going backwards or we don't see progress and the automatic assumption is that we need to train more, train harder rather than training smarter - it is the opposite. Rest is as important as the training itself and this is one of the reasons cardio on the off days can be a self-defeating, goal-crushing behaviour. I say reduce the exercises, focus on building up the big compound movements a couple of times a week and then see a marked difference in results and time spent in the gym.

If you want to lose fat but fear being skinny, then you likely don't have what you perceive to be enough muscle. If you don't have enough muscle then you likely don't have enough strength. So I would say get back on the strength goals and then let those take care of the body fat too. Body fat for most part is diet, but you can pump out volume sets of heavy weights that will burn up a shitload of calories too. I do no cardio, don't have a fantastic diet (it's decent) and sit happily around 10% bf. But I may well be what you would consider skinny...

Will give Birds props for working out smarter than he was previously.

Basketball counts as cardio I'd say.

I would say you're skinny (or skinnier than I would want to be), but I still have hangups about being skinny so my opinion may not be objective enough.

Also, I dropped a few KGs while on Holiday despite eating a ton of short bread and bad foods... I put it down to spending a lot of time running around with/after the grub which was very fun.

Edited by ActionDan

Basketball isn't cardio?

Definitely cardio, but I don't gain or lose any noticeable fat in the off season. It's also more HIIT, given the short sprint nature of the game and my usual position as a centre. It does get in my way a bit, but I love basketball too much to give it up for gym goals. It's also good plyometric training for the functional side of being strong.

The point is, as a beginner, he should be resting more and eating above maintenance to promote muscle repair and growth.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Any update on this one? did you manage to get it fixed?    i'm having the same issue with my r34 and i believe its to do with the smart entry (keyless) control module but cant be sure without forking out to get a replacement  
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if something was binding the shaft from rotating properly. I got absolutely no voltage reading out of the sensor no matter how fast I turned the shaft. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • So this being my first contribution to the SAU forums, I'd like to present and show how I had to solve probably one of the most annoying fixes on any car I've owned: replacing a speedometer (or "speedo") sensor on my newly acquired Series 1 Stagea 260RS Autech Version. I'm simply documenting how I went about to fix this issue, and as I understand it is relatively rare to happen to this generation of cars, it is a gigantic PITA so I hope this helps serve as reference to anyone else who may encounter this issue. NOTE: Although I say this is meant for the 260RS, because the gearbox/drivetrain is shared with the R33 GTR with the 5-speed manual, the application should be exactly the same. Background So after driving my new-to-me Stagea for about 1500km, one night while driving home the speedometer and odometer suddenly stopped working. No clunking noise, no indication something was broken, the speedometer would just stop reading anything and the odometer stopped going up. This is a huge worry for me, because my car is relatively low mileage (only 45k km when purchased) so although I plan to own the car for a long time, a mismatched odometer reading would be hugely detrimental to resale should the day come to sell the car. Thankfully this only occurred a mile or two from home so it wasn't extremely significant. Also, the OCD part of me would be extremely irked if the numbers that showed on my dash doesn't match the actual ageing of the car. Diagnosing I had been in communication with the well renown GTR shop in the USA, U.P.garage up near University Point in Washington state. After some back and forth they said it could be one of two things: 1) The speedometer sensor that goes into the transfer case is broken 2) The actual cluster has a component that went kaput. They said this is common in older Nissan gauge clusters and that would indicate a rebuild is necessary. As I tried to figure out if it was problem #1, I resolved problem #2 by sending my cluster over to Relentless Motorsports in Dallas, TX, whom is local to me and does cluster and ECU rebuilds. He is a one man operation who meticulously replaces every chip, resistor, capacitor, and electronic component on the PCB's on a wide variety of classic and modern cars. His specialty is Lexus and Toyota, but he came highly recommended by Erik of U.P.garage since he does the rebuilds for them on GTR clusters.  For those that don't know, on R32 and R33 GTR gearboxes, the speedometer sensor is mounted in the transfer case and is purely an analog mini "generator" (opposite of an alternator essentially). Based on the speed the sensor spins it generates an AC sine wave voltage up to 5V, and sends that via two wires up to the cluster which then interprets it via the speedometer dial. The signal does NOT go to the ECU first, the wiring goes to the cluster first then the ECU after (or so I'm told).  Problems/Roadblocks I first removed the part from the car on the underside of the transfer case (drain your transfer case fluid/ATF first, guess who found out that the hard way?), and noted the transfer case fluid was EXTREMELY black, most likely never changed on my car. When attempting to turn the gears it felt extremely gritty, as if shttps://imgur.com/6TQCG3xomething was binding the shaft from rotating properly. After having to reflow the solder on my AFM sensors based on another SAU guide here, I attempted to disassemble the silicone seal on the back of the sensor to see what happened inside the sensor; turns out, it basically disintegrated itself. Wonderful. Not only had the electrical components destroyed themselves, the magnetic portion on what I thought was on the shaft also chipped and was broken. Solution So solution: find a spare part right? Wrong. Nissan has long discontinued the proper sensor part number 32702-21U19, and it is no longer obtainable either through Nissan NSA or Nissan Japan. I was SOL without proper speed or mileage readings unless I figured out a way to replace this sensor. After tons of Googling and searching on SAU, I found that there IS however a sensor that looks almost exactly like the R33/260RS one: a sensor meant for the R33/R34 GTT and GTS-T with the 5 speed manual. The part number was 25010-21U00, and the body, plug, and shaft all looked exactly the same. The gear was different at the end, but knowing the sensor's gear is held on with a circlip, I figured I could just order the part and swap the gears. Cue me ordering a new part from JustJap down in Kirrawee, NSW, then waiting almost 3 weeks for shipping and customs clearing. The part finally arrives and what did I find? The freaking shaft lengths don't match. $&%* I discussed with Erik how to proceed, and figuring that I basically destroyed the sensor trying to get the shaft out of the damaged sensor from my car. we deemed it too dangerous to try and attempt to swap shafts to the correct length. I had to find a local CNC machinist to help me cut and notch down the shaft. After tons of frantic calling on a Friday afternoon, I managed to get hold of someone and he said he'd be able to do it over half a week. I sent him photos and had him take measurements to match not only the correct length and notch fitment, but also a groove to machine out to hold the retentive circlip. And the end result? *chef's kiss* Perfect. Since I didn't have pliers with me when I picked up the items, I tested the old gear and circlip on. Perfect fit. After that it was simply swapping out the plug bracket to the new sensor, mount it on the transfer case, refill with ATF/Nissan Matic Fluid D, then test out function. Thankfully with the rebuilt cluster and the new sensor, both the speedometer and odometer and now working properly!   And there you have it. About 5-6 weeks of headaches wrapped up in a 15 minute photo essay. As I was told it is rare for sensors of this generation to die so dramatically, but you never know what could go wrong with a 25+ year old car. I HOPE that no one else has to go through this problem like I did, so with my take on a solution I hope it helps others who may encounter this issue in the future. For the TL;DR: 1) Sensor breaks. 2) Find a replacement GTT/GTS-T sensor. 3) Find a CNC machinist to have you cut it down to proper specs. 4) Reinstall then pray to the JDM gods.   Hope this guide/story helps anyone else encountering this problem!
    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
×
×
  • Create New...