Mr. Keets Posted May 2, 2009 Share Posted May 2, 2009 Good news Paul. Are you putting it on the dyno??? Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4570051 Share on other sites More sharing options...
Piggaz Posted May 2, 2009 Share Posted May 2, 2009 Fitting a Kakitmoto Mega N1 exhaust on monday (3.5 inch up fonr a 3 inch) then off to unigroup for a tune. Within the next few weeks i hope. Cant wait to be able to drive a non timing retarded, mega rich black smoke blowing, slug again! haha. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4570293 Share on other sites More sharing options...
Beer Baron Posted May 19, 2009 Share Posted May 19, 2009 hopefully they will reimburse you the $210. that is surely cheaper than if you had used their fed-ex account to send it back, then they balance it, then send it back. the one way postage alone would have been $210. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4603800 Share on other sites More sharing options...
wrxkilla Posted May 19, 2009 Share Posted May 19, 2009 mines been at a balancing place for a bit. will chase it all up tomorrow and let you guys know how mine has gone north of the border.... mick Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4603987 Share on other sites More sharing options...
Piggaz Posted May 20, 2009 Share Posted May 20, 2009 Any idea how much your balance will cost you Michael? Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4606041 Share on other sites More sharing options...
Piggaz Posted May 31, 2009 Share Posted May 31, 2009 Thought i'd report back again . Got the shaft in last night. I think being a one piece it must transmit more NHV through the driveline. Its not unbalanced as such (well there isnt any one speed where it shakes the car like it used to). Of the guys that have fitted their's, have you found the same thing? On a side note car gets tuned on tuesday. Woohoo! Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4627559 Share on other sites More sharing options...
Mr. Keets Posted June 1, 2009 Share Posted June 1, 2009 Good news Paul. I haven't really noticed any increase in NVH to be honest, but I don't drive it every week. I have a small vibration from the OSG 5 speed that needs attention... 3rd gear light to medium acceleration only. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4628931 Share on other sites More sharing options...
Piggaz Posted June 1, 2009 Share Posted June 1, 2009 Good news Paul. I haven't really noticed any increase in NVH to be honest, but I don't drive it every week. I have a small vibration from the OSG 5 speed that needs attention... 3rd gear light to medium acceleration only. Vibration after putting in the OSG 5 speed. I have that EXACT issue. ONLY in 3rd though. I have gotten rid of most of it by putting in rear sub frame locking collars. 90% dissapeared. How many kms have you put on it? Ive done 1200 and although its not getting any worse... it aint getting any better. I have rung up and spoken to quite a few people about this but they all say it isnt the gearbox! If you do manage to fix the issue please let me know what you did! Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4629085 Share on other sites More sharing options...
elrodeo666 Posted June 1, 2009 Share Posted June 1, 2009 I'm interested in this as well as got OSG 5 speed on order.. Vibration after putting in the OSG 5 speed. I have that EXACT issue. ONLY in 3rd though. I have gotten rid of most of it by putting in rear sub frame locking collars. 90% dissapeared. How many kms have you put on it? Ive done 1200 and although its not getting any worse... it aint getting any better. I have rung up and spoken to quite a few people about this but they all say it isnt the gearbox! If you do manage to fix the issue please let me know what you did! Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4629312 Share on other sites More sharing options...
Piggaz Posted June 1, 2009 Share Posted June 1, 2009 Mr. Keets and elrodeo666 did you buy the billet centre plate? If it makes any difference i have one in mine! Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4629528 Share on other sites More sharing options...
Mr. Keets Posted June 1, 2009 Share Posted June 1, 2009 Paul, Mark No billet plate, I wouldn't have 2,500Km on the box yet. A mate told me it might have been a bearing run out issue...not sure. I'm home in the first week of July so I'll have the shop pull it down and go through it again. Definitive answer...here's hoping. On second thoughts I might just get the centre bearing replaced on the standard shaft(s) and see if that changes it. If not...then it's the box Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4629602 Share on other sites More sharing options...
Piggaz Posted June 1, 2009 Share Posted June 1, 2009 ^^ Well I have the same 3rd gear vibration with both the stock shaft and and the carbon one. When i built my box i replaced all bearings with new NSK sealed units. Either way it will be interesting to see what comes out of you pulling yours apart. The bloke that built my box also used that yellow paint on the gears to make sure they were all meshing correctly... Everything seemed 100%. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4629709 Share on other sites More sharing options...
Mr. Keets Posted June 1, 2009 Share Posted June 1, 2009 mmmm. I couldn't tell as my centre bearing was on the way out anyway. The cat who built mine has built a number for my tuner. I'm not aware of anyone else from that shop with a prob...I might put a thread in the drivetrain section tomorrow + the UK forum. EDIT: Done 5 speed vibration: SAU Drivetrain sub forum Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4629876 Share on other sites More sharing options...
Angus Smart Posted June 9, 2009 Author Share Posted June 9, 2009 Hey guys glad the shaft saga is sorting itself out any reply from acpt about balancing yet?? still waiting on my motor to go back in so will have to see what becomes of the shaft then (i still dont know if its going to fit with my r34 getrag in the 32..) Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4644829 Share on other sites More sharing options...
AtomicBomberMan Posted June 9, 2009 Share Posted June 9, 2009 Didn't any of you guys read the acpt motto before your purchase? EXPERIENCE MAKES ALL THE DIFFERENCE! so true so true.......what an experience! I bought a pst shaft when darren was doing a group buy. I spoke to pst personally, and their service is excellent. All the extra time and money that you guys have spent has really made this such a sour experience. If anyone would like carbon shaft, shoot dazmo a pm and he would be glad to help you out. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4646372 Share on other sites More sharing options...
Piggaz Posted June 14, 2009 Share Posted June 14, 2009 Another report back Car has been tuned and i took it for a long drive yesterday. This shaft is going back to where it came from. There is a vibration/grumble at 70, goes away at 82ish then comes back at 100 then anything up from there it just gets worse and worse (not anywhere as bad as before. Anything over 120 you really cant see anyting out of the rear vision mirror). Also what i noticed was when you feed the power on it makes more of a noise then if you are just cruising. Im so over this thing! Going to WSID on wednesday so maybe a 7500 RPM launch might sort it out haha. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4654935 Share on other sites More sharing options...
Mr. Keets Posted June 14, 2009 Share Posted June 14, 2009 What a nightmare Paul. Sorry to hear it. 7500 side step FTW Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4655174 Share on other sites More sharing options...
Angus Smart Posted June 16, 2009 Author Share Posted June 16, 2009 f**k what a shit fight.. Any news on the later one that got replaced when it shattered in WA?? the replacement one seems like it was ok.. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4659136 Share on other sites More sharing options...
Mr. Keets Posted June 16, 2009 Share Posted June 16, 2009 Haven't heard...no news is good news on this deal I guess. Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4659432 Share on other sites More sharing options...
Piggaz Posted June 16, 2009 Share Posted June 16, 2009 In 2 minds how to go about this. Seeing that I got it rebalanced externally from them, the might not accept it. However when/if these guys do accept it back they will probebrly put it on some sort of machine to see if it is out. Now the guy that I got it balaced up through did say it is perfectly straight and is reading "0" on the machine. Bah humbug! Link to comment https://www.sau.com.au/forums/topic/208678-group-buy-acpt-carbon-fibre-tailshafts-any-model-1400us/page/35/#findComment-4659771 Share on other sites More sharing options...
Recommended Posts