Jump to content
SAU Community

Recommended Posts

bit more of an update....forgot to add this....you will need to machine off about 2mm of the hub.....don't worry it does not affect anything.....but if you don't do it it will rub against the rotor.

I didn't need to do this. R32 GTR 32mm discs. about 1.5mm clearance. drives fine. I will add after removing the olive in the caliper to grab a very fine tooth file to smooth the mating surface of the banjo bolt cooper washer to ensure a good seal.

I didn't need to do this. R32 GTR 32mm discs. about 1.5mm clearance. drives fine. I will add after removing the olive in the caliper to grab a very fine tooth file to smooth the mating surface of the banjo bolt cooper washer to ensure a good seal.

hmmm....your the second person to say this to me.....Scott said the same thing.......he even has my old R32 rotors. In saying that I had to remove this area on mine and Andy's AR-X.....maybe there is a difference in the offset between the RX and AR-X.

hmmm....your the second person to say this to me.....Scott said the same thing.......he even has my old R32 rotors. In saying that I had to remove this area on mine and Andy's AR-X.....maybe there is a difference in the offset between the RX and AR-X.

If the Hub Bearings are different it could change the offset...maybe

I will also say, if your brake discs are currently warped to sort them out asap. I think I left mine to long and it has worn my power steering rack to the stage I now get shudder when turning the wheel quickly.

If the Hub Bearings are different it could change the offset...maybe

I will also say, if your brake discs are currently warped to sort them out asap. I think I left mine to long and it has worn my power steering rack to the stage I now get shudder when turning the wheel quickly.

The hub bearings are the same part number....maybe the upright is slightly different! Never had the brakes warped on the front of this car but I do get a shudder on left hand sweepers under power.....reckon its the CV's on the LH shaft or steering rack? Need to get it sorted....or maybe just don't turn left....lol.

The hub bearings are the same part number....maybe the upright is slightly different! Never had the brakes warped on the front of this car but I do get a shudder on left hand sweepers under power.....reckon its the CV's on the LH shaft or steering rack? Need to get it sorted....or maybe just don't turn left....lol.

Roger that, who knows then.

I checked my rack end play...definately what my issue is. Only happens when I turn right under power or sitting dead still and turning the wheel quickly.

The hub bearings are the same part number....maybe the upright is slightly different! Never had the brakes warped on the front of this car but I do get a shudder on left hand sweepers under power.....reckon its the CV's on the LH shaft or steering rack? Need to get it sorted....or maybe just don't turn left....lol.

I had the same 2mm disk clearance, ARX must have different front end which would make sense if the strut has 40mm extra travel.

  • 1 month later...
  • 2 weeks later...
does anybody have the DBA code for standard rear M35 brakes?? the maxima and xtrail dont show rears on the dba website..

thanks

from the DBA website... Perhaps try looking for 350z Touring brakes :)

4000 Series Performance Brake Rotors

Position DBA # IRP$ (AU$) [?] Description Dia. x Thick.(mm)

Rear DBA4574 $275.52 ea 4000 Series Standard Left/right-hand Vented 292 x 16

Front DBA4954 $250.47 ea 4000 Series Standard Left/right-hand Vented 296 x 24

Position DBA # IRP$ (AU$) [?] Description Dia. x Thick.(mm)

Rear DBA4574SL $325.61 ea 4000 Series Slotted Left-hand Vented 292 x 16

Rear DBA4574SR $325.61 ea 4000 Series Slotted Right-hand Vented 292 x 16

Front DBA4954SL $300.56 ea 4000 Series Slotted Left-hand Vented 296 x 24

Front DBA4954SR $300.56 ea 4000 Series Slotted Right-hand Vented 296 x 24

Position DBA # IRP$ (AU$) [?] Description Dia. x Thick.(mm)

Rear DBA4574XS $375.71 ea 4000 Series Xs Left/right-hand Vented 292 x 16

Front DBA4954XS $350.66 ea 4000 Series Xs Left/right-hand Vented 296 x 24

Street Series Increased Braking Performance

Position DBA # IRP$ (AU$) [?] Description Dia. x Thick.(mm)

Rear DBA574 $122.45 ea Street Series Standard Left/right-hand Vented 292 x 16

Front DBA954 $163.69 ea Street Series Standard Left/right-hand Vented 296 x 24

Position DBA # IRP$ (AU$) [?] Description Dia. x Thick.(mm)

Rear DBA574SL $197.87 ea Street Series Slotted Left-hand Vented 292 x 16

Rear DBA574SR $197.87 ea Street Series Slotted Right-hand Vented 292 x 16

Front DBA954SL $222.92 ea Street Series Slotted Left-hand Vented 296 x 24

Front DBA954SR $222.92 ea Street Series Slotted Right-hand Vented 296 x 24

Position DBA # IRP$ (AU$) [?] Description Dia. x Thick.(mm)

Rear DBA574X $222.92 ea Street Series Gold Left/right-hand Vented 292 x 16

Front DBA954X $275.52 ea Street Series Gold Left/right-hand Vented 296 x 24

Edited by iamhe77
  • 5 months later...

I'm looking at getting DBA rotors for the wagon.

The existing slotted discs it came with are getting too thin.

They don't like the heat generated slowing the M35 down hills like Stanwell Tops and Kangaroo Valley and keep warping.

Trying to decide between the DBA954X / DBA574X which are their 'Street' Gold cross drilled and the more expensive 4000 series rotors, either slotted or cross drilled.

Is there anything wrong with the cheaper 'Street' brakes, I've come across a few posts where people claim they've heard of some bloke cracking cross drilled brakes, but it seems a bit like an old wives tail.

I don't want to spend money pointlessly, but brakes are the place to go a bit nuts.

Any other good rotor replacements for stock calipers? I've seen the RDA ones on ebay, but I can't find any good info on their full range.

Thanks

They bolt on perfectly, a couple of us have done the conversion.

Are you selling yours? PM me a price if you are.

Need to source me a set of these.

Edited by Paramour

I'm looking at getting DBA rotors for the wagon.

The existing slotted discs it came with are getting too thin.

They don't like the heat generated slowing the M35 down hills like Stanwell Tops and Kangaroo Valley and keep warping.

Trying to decide between the DBA954X / DBA574X which are their 'Street' Gold cross drilled and the more expensive 4000 series rotors, either slotted or cross drilled.

Is there anything wrong with the cheaper 'Street' brakes, I've come across a few posts where people claim they've heard of some bloke cracking cross drilled brakes, but it seems a bit like an old wives tail.

Do you want to find out the hard way? Get slotted but not drilled.

Do you want to find out the hard way? Get slotted but not drilled.

I'm leaning towards the slotted after doing more reading.

This link (provided by GSLRallySport) pretty much describes my problem

http://www.stoptech.com/tech_info/wp_warped_brakedisk.shtml

Save a bit of cash and spend it on pads...

I had the same 2mm disk clearance, ARX must have different front end which would make sense if the strut has 40mm extra travel.

hey buddy....what you say?????

P.S. I know I'm a smart arse!

  • 1 month later...

Having done a fair bit of reading on brakes (zomg theres a search button!) I was just wondering whether slotted rotors and good pads with the standard calipers is a worthwhile upgrade or if the only way forward is a caliper upgrade?

Seems like there are heaps of options, k sport, 350z brembos, akebonos, but I'm curious if theyre worth the premium for a road car...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...