Jump to content
SAU Community

Haltech R35 Gt-r Dyno & Drag Results Thread


Recommended Posts

11.1 and 126mph from a car that weighs 1740kg, and has had no mechanical changes, is nothing short of staggering.

all hail the new king of performance cars

Maybe the new ecu is a cuppla hundred kg lighter than the factory jobbie. :banana::teehee:

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

fantastic result for first time out!!

i remember being happy when my evo ran 12.4 with autronic, 3 inch turbo back exhaust, aps cold air induction, etc

boost incease and tune & 11.1 @ 124 excellent! 10's are coming very soon

So what happens when they make some more adjustments to the tuning and on a good warm day it runs a 10.9sec and they are forced to put a cage in it, will they?

Because it can't be more than a month away before it does run a 10sec pass but I can't see them wanting to strip out a perfect good R35 just to run another 10sec pass.

Its interesting that it had a higher trap speed on the third run, without the correct launch control (which as far as I understand is just the equivalent of dumping the clutch in a manual). I wonder what happened there...

very impressive especially considering that it's running street tyres. imagine what gains there would be with some semi slicks or even better some proper drag radials. :)

I think it might be a bit of a challenge fitting the 255/50/16 radials over those gi-normous brakes. :)

But running a 10 with basic mods on factory rubber and stock everything else including exhaust is phenominal. Just shows you how well this car has been designed and engineered.

Sign me up...

though I don't know if an owner would want to modify a street driven one it while its still under factory warranty if it will void the warranty... what do you guys think?

Depends on how cashed up they are?

If the purchase price was the absolute max they could afford, then I guess they wouldn't.

However, if $$$ aren't a major factor then anything goes...

Yeah definately with that mile on the third run it would have been a 10 second pass!, our first 10 pass was 10.8@ 129 mph

so the haltech gtr with a good launch is already capable of 10's. excellent result.

Edited by giant

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...