Jump to content
SAU Community

Recommended Posts

Hey Guys and Girls.

So i'm hopping to buy a Stagea in a couple of months time...depending on when i can secure finance. Lol.

And the only major worry I have at the moment is that it will be auto, cause as u all would know Manual versions are hard to come by.

Anyways im looking at getting around a 1998 RS4 (Series 2) and i will be wanting to convert it to manual.

So if everyone who has done this can post up their gearbox/clutch combinations...and how they think they go and what they cost you.

Or if you have a wrough idea.

Thanks Matt

PS. I will be wanting decent power figures in the future and don't want to be replacing parts so i will be open to spending a bit more money for decent parts.

Link to comment
https://www.sau.com.au/forums/topic/226245-stagea-gearbox-questions/
Share on other sites

Dude, with manuals going at prices like these

http://www.j-spec.com.au/list/index.php?ID=12974

you aren't going to convert one any cheaper.

or this

http://www.j-spec.com.au/list/index.php?ID=12864

(no, I dunno what the hell a "B Spec" is either..)

or this

http://www.j-spec.com.au/list/index.php?ID=12863

I did manual conversion, and i will never do it again. I've had a bad run with dodgy gearboxes, but aside from that, there's no value in buying an auto just to convert it, you're better off getting a manual one already.

I did a manual conversion with a 32 gtr box i had lying around from the race car, it was all pretty strightforward. but if you had to pay for the parts and a workshop to do the work it would be $6k+ easy.

but if you don't really like autos, just buy a s2 manual. the autos are slugs.

Thanks guys.

I was hopping to get one with low Ks on it...and from what i've seen "Manual" and "Low Ks" dont go together. So hence my choice to convert an auto.

Does anyone have a good idea of combinations...what will best match up with the stageas drive line?

Thanks guys.

I was hopping to get one with low Ks on it...and from what i've seen "Manual" and "Low Ks" dont go together. So hence my choice to convert an auto.

Does anyone have a good idea of combinations...what will best match up with the stageas drive line?

Buy a manual.

If you're determined to convert there is heaps of information in the DIY section above:

Manual conversion check list

2 "how to" threads

one on why not to convert

(editted - having regard to your comments on having problems finding a low mileage example)!

All the 4wd boxes will work fine, they are all the same length. There is a difference in diff ratios but the gearbox does not affect that (well maybe avoid the 34 gtr one it is very short).

as i said above i used 32 gtr, I think it is the best bet - cheapest and bolts straight in. Most use a push type clutch which are cheaper than pull type clutch from 33 and 34 gtr. pretty sure 32 gts4 is the same as 32 gtr as well. they go for about 800 second hand.

more expensive is the console. handbrake and clutch and brake pedal boxes are pretty cheap. cut a hole thru the floor for the shifter and that is about it, but the detailed threads above have lots of good info including all part numbers.

I am very happy with the outcome of the conversion (it is great to drive manual, best car I've had apart from the fuel consumption). But as said above it will be cheaper to just buy a manual unless you have most of the bits lying around like I did

i have an R33 with 196,000 km on it (plus the RS4S). the R33 has been pushing out over 200rwkw since i bought it 7 years ago. compression is sweet across the board.

120,00km is nothing.

buy the manual in the first place from any of the guys selling locally and you will be laughing. alternatively wait for one at auction and then the hassles of waiting for it to get on a boat, compliance and maintenance and repairs (ie coils, clutch etc). either way it will work out much easier and possibly cheaper than converting one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...