Jump to content
SAU Community

Recommended Posts

maybe... but if you want big power out of a nissan.... it's forged piston and rebuilt internals time anyway...

I paid $100 for the T25 Turbo (for silvia remember)

$100 for manifold

$200 in oil lines. intercooler piping and miscilanious gear...

for $400 it's really really cheap....

don't be scared do the work yourself... especially if you can drive your girls car...

it actually gives you an attachment to your car... you built it and it really does give you satisfaction when driving it that you have built it yourself...

I understand the whole just buy a turbo car though... I depends what you want... mine is just a little added boost until I rebuild with forged pistons... 30/37 and custom manifolds...

should be fun... it will still be with the NA motor... just the only thing that doesn't like the boost is the NA pistons.... other than that the motor is virtually identical...

the oil squirters I hear you all say... how many 1000Hp V8's have crank case oil squirters... I've already looked into it and done the calcs(well my mechanical Engineer father did.) and he reckons that sure they are cool but you don't need them....

anyway dudes have fun just remember.... make a plan research and do it cheap.... it's the Garage Spank Moto......

  • Replies 321
  • Created
  • Last Reply

Top Posters In This Topic

Originally posted by 33Spec2

Which is cheaper fitting a turbo or gettin a half cut? Which is better? Has anyone found out any prices?

Another thing will insurance b about the same as a gts-t?

Thanx

it will definately cost more for getting a half cut (i just bought a rear end so i could have rear gtst diff, hubs, breaks and 5 stud :()

with insurance for some reason the car is insured under my name (didnt know) 3rd party (i knew this but thought under my name) as a GTST!

so all im gonna do is say "my engine blew coz it was running bad, so i found a good one and put it in and its fine now heres the engine number"

and yeah :D

Guest neoGT-25

Hey all, at school and the PC's are slow as!

I was told yesterday to go 2.25" on my exhaust? 2 people from Sub Zero told me and i dont know what to think?

most of you guys have 2.5" am i right?

im also thinkong of cold air induction and extractors? good idea?

anyway g2g, byes all :burnout:

PS: Hey boxhead, when you get ya new ride you betta still be on this thread!

if you get a 2.5" then make sure you get a good resonator and muffler that takes out the drone. else it will drone and annoy you!

personally, next time around i'd get a 2.25", i think its a bit more responsive with a 2.25".

guys my car might be for sale soon! new job means new car! yay!

i went ahead and got those rims that were on a silvia.

they are 16x7 front and 16x8 rear, and the offset on both is 32mm. They fit perfectly with no rubbing at all on full lock, and no rim hanging out of the gaurd.

I therefore conclude that the correct offset for 16" rims to fit a non turbo R33 GTS is 32mm

Neogt25: i would go with 2.25" piping. If you want 2.5" piping make sure you get at least one resonator and use a good quality muffler (as turtle said). I have 2.5" piping with 2 resonators and a quality muffler (HKS system) and i still get a bit of drone from 2-3k rpm. hope this helps.

well i sold my n/a engine today for 800 without the box :D :D

it is going to be used for an rb25/30deTT buildup going into a vl. the person who bought it had his mate with him who has a rb26/30dett in his own vl

good to see my engine will be contributing to something special

to bad in a vl but lol :D

ARGH CANT WAIT TIL I HAVE MY CAR BACK!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...