Jump to content
SAU Community

Recommended Posts

Hey guys, I'm referring to the car washes where you pay $1 for 1 minute of pressure spray/ de-greaser/ soap etc.

Ok so my engine bay is filthy and all dirty.. Can i just pressure spray it and degrease it without damaging anything.. is it something i can do? how else would i clean it?

Link to comment
https://www.sau.com.au/forums/topic/237640-1-per-minute-car-wash/
Share on other sites

Mixed responses you will have for this.

I have used this technique for a friends r32 gts-t at those carwashes and all we did was put a plastic bag over the pod filter.

my ex bmw i used to hand wash all the time as i would was the car and hose it down

my ex r33 i would spray citrus based degreaser in a can over the tough spots and hose down

never had a problem but i would use a chammy to dry as much water as possible then start the car and drive it for at least 15minutes to evaporate any water left

hope that helps

it can be done, but you have to be careful. It wudnt hurt to cover a few things such as Pod, Alternator, Sparkplug cover and the electrical connectors. Thing is, you dont necessarily NEED to cover them, however it will just attract rust. Im sure you dont want your connectors/plugs/pins do develop rust.

This is what i do. I spend say 1 weekend and clean 1 area of the engine bay. I try to take out as many parts as i can, then i give it a good clean with some "Prestone Bug n tar remover" and then polish it off! squeaky clean. The bug n tar remover works wonders on the rocker covers too. I know its a pain but that way i dont compromise my engine in anyway, esp water damage.

Safest option is get a can of degreaser and a cloth and go nuts. Will take you a while, but its better than having water in any electrical system under your bonnet.

+1

This is what I do, only takes 15min if your not too pedantic

You'll be fine :cool:

Most car dealers get a waterblaster, spray the bay with it, then once it dries spray it with silicone, plastic bag over the pod might be a good idea though

If you have an oil squirting air compressed gun, you can put degreaser and water into it and spray your bay, I did that to mine, no rust 4 years after

I did it with my 33, was fine till you hit 4000rpm then it would not rev any more and if you put your foot into it below 4k it would break down all the time, happened for about 5 mins parked it at a mates for about an hour and never had a problem since.

So long as you dont direct and pressure for prolonged periods it will be fine.

As in just spray your degreaser over everything, let it soak for a min then just gently hose it off with the garden hose.

Maybe give certian areas a scrub with a brush if you need to.

Basically avoid hard sprays at areas such as fuseboxes, pods, alternator (although it is low and probly gets wet frum underbody water in the rain anyway) and the lead cover/leads.

If you jam the hose under the lead cover to clean it out then your just asking for trouble.

I used to do this all the time on my Integra Type R, and never had a problem once with cutting out, rust etc etc. Just a nice clean engine! ;) Will be doing this on my R33 today when i was her. As i did a coolant change/flush last night so theres a bit to clean up.

If you put degreaser on and not wash it off properly it stinks like shit though...

In my 33 I spray the shit out of it with degreaser then just hose it off... looks brand new after 5 minutes at home

If you put degreaser on and not wash it off properly it stinks like shit though...

In my 33 I spray the shit out of it with degreaser then just hose it off... looks brand new after 5 minutes at home

Not if you use "Simple Green" :(

That stuff smells good hahaha, and its the best degreaser out!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...