Jump to content
SAU Community

Recommended Posts

Not everyone running ethanol is a tightarse, some run it because its a better (higher octane) fuel, Holden are banking on people running it for no power increase, just to make you feel warm, fuzzy and green. It has worked out around the same cost as 98 for me per km, but with a much higher power output.

I run ethanol because I hated the sound of my engine pinging on a hot day, I wanted to run stupid boost, and the 30% extra torque was a great bonus. Plus much of my hard earned is staying in Australia, some even going to our poor farmers.

Is there a better fuel you can buy from the pump?

Dont get me wrong Im not against it I run e85 and im the last person that gives a shit about consumption as I constantly drive on boost getting prob 250km to a tank which I dont complain about, what im saying is that the people that are saying its cheaper then petrol thats its not quite right just cause its 20cents cheaper a litre but as I said I went on it for the gains of power and safer on the engine as you said

  • 2 weeks later...

Filled up a Jerry at Caltex Footscray but it was very slow!!!! They told me they had fuel but the pump was stuffed. Going there later to try and fill up, otherwise its back to 98.

The Springvale pump does the same thing, just hang it up and start again. It seems to do it when they don't enable the pump quick enough.

I've been searching the web for a while regarding e85 into a rotax Kart engine.

i'm about dew for a full rebuild on my motor and wanted to give e85 a go before i do so..

the carb has fixed jets, that re changed by removing and replacing with larger/smaller jet

Heres a little bit of reading on tuning.. if someone could tell me what i'd need to do to get e85 going would be great :)

Next you will need to install the proper Main Jet for the current conditions. Remember that the proper main jet can only be determined by knowing all of the following conditions:

Temperature

Humidity

Barometric Pressure

Altitude

Once the Main Jet is installed and the carburetor reassembled, you will be ready to install it back on the motor. Be sure to tighten the hose clamps and that all of the bolts are tight as well.

Take the kart out on the track and observe proper 'warm-up' procedures. Once the engine is warmed up, begin pushing it to its limits.

LOW RPM TUNING - If the kart runs rough at lower RPM's (5,500 - 8,500), we need to adjust the needle setting to be 'leaner'. How 'rough' it is running should determine this adjustment. Never adjust more than (2) grooves in any direction, this can cause a low RPM seizure.

HIGH RPM TUNING - If the motor will not rev cleanly from 10,000 RPM through to 12,500 then change the main jet to ONE jet lower. For example, if you are running a 168 jet and the motor pulls well through 11,500 and begins to break up or bog at 12,000 you should change to a 165 main jet. If the leaner jet seems to help, but still does not feel 100% right, consult your plug reading to determine if a leaner jet is suitable. BE VERY CAREFUL. At this point, going too lean could cause an engine seizure. Once you have found the appropriate main jet, it is possible you may have to change the clip setting to eliminate any lower RPM bog.

If the 'leaner' jet does not remedy the problem, you should install a jet that is one size bigger (richer).

The indications of a jet that is too lean can include a loud 'popping,' or a sudden drop off in performance at high RPM.

Any time the jet seems too lean you should consider immediately coming in to the pits, getting a good 'cut' on the plug and reading your plug indicators.

try getting a jet literally 30% bigger than your current jet, then check AFRs or if not possible, check egt with a temp gun and compare to your current egt with petrol.

then once set try adding some timing and see how you go with it. you should try and have some way of testing the power, ie 0-100kph with petrol vs 0-100kph with e85 + more timing, let us know how you go

did another e85 test on the current batch of Caltex bio-eflex

http://www.mrparts.com.au/MPRacing/?p=460

Very interesting, thanks for the posting that. Wouldnt the United E85 (really E95) have issues with cold start in the winter?

I thought someone in this thread mentioned that Caltex have never gone to their summer mix and so far have just stayed with their low 70's winter mix? Did you get a chance to test Caltex during summer?

Flash point of Ethanol is 13deg and petrol around -40deg

By my calculations the flash point should be around the following...

E95 = 10deg

E85 = 5deg

E70 = 1deg

These are only approximate figures but they wouldn't be too far off. I know for over here in WA we could probably get away with E95 all year around as it only really drops below 10deg ambient in winter on cold mornings.

For colder weather like Melbourne you would probably get away with E85 all year around, E70 maybe for super cold mornings...

Realistically Australia has a fairly hot climate and there is no real need for winter mix (car may take a few more turn overs in winter) but remember they are selling to non car enthusiasts as well who may consider the extra cranking a problem/issue

Edited by SimonR32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
    • I was able to get some underside photos while the car was on the ramp The suspension is all Altezza/IS200/IS300 so getting part's will hopefully be less of a headache
    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
×
×
  • Create New...