Jump to content
SAU Community

Recommended Posts

they're the same "98 octane" so is it ok to mix petrols?

or just stick to the onoe bp ultimate? :devil:

there is really no difference between BP98, mobil 98, caltex 98, shell 98. the only differences you get is between servos and batches. sometimes any company will have a bad batch, or some contamination, or you are unlucky enough to buy from a servo with low stock (ie getting fuel from the bottom of the tank) or with old stock. but apart from that it doesn't matter one bit really which 98 brand fuel you buy.

spent a week cruising the hinterland behind coffs harbour last year while the old girl did some business there. I had the luxury of a BP, Shell, and a caltex within 5 minutes of where i was staying so i tried them all. The caltex returned the lowest knock reading of them all. Only talking a couple of points and, as has already been pointed out it could just be different batches causing the slight variance But i wouldnt worry about using any of those 3 in a car tuned to 98 fuel.

Edited by FineLine

well unless i got a bad batch i will have to disagree with everyone

My car was tuned with bp ultimate 98, i never got above 12 no matter what i did

I put in some Caltex vortex 98 and my knock values went through the roof at high rpm. I went to 6900rpm and knock when from 6 to 66 in an instant.

Tune was spot on too

i dunno what it is guys...but in my stock r32 gtst before the half line i can get 230kms with bp ultimate...as soon as i change to something like v power i can get about just over 200-210kms at half way?

but yeh don't think there are probs with mixing petrols...the focus, corolla, swift daily drivers in most cases would probably switch from 4 different brand fuels because they would most likely get whatever is close to them at the time of needing fuel.

I use BP98, Mobil 98 and united 98. Find no difference between either of them. Unless your sitting on the freeway doing the exact speed and accelerating up to speed the same you cannot tell the difference. You might floor it harder for longer 3 times more in 1 whole tank of driving.....you might drive for an hour longer in slightly warmer weather which should make it run slightly richer (depending on ecu).

In terms of knock the turn over the servo has plays a big part in the age of the fuel. Try to fill up at servos that a fairly busy.

  • 2 years later...

@llusions lol I've done the same thing. I realised after putting about 20L in, so just stopped and picked up the 98 and waited for the staff to unlock. You'll be fine running even 91 as long as it is in low ratio, ie 10L out of 60L tank, with the rest being 98 but not recommended. A friend in the country says he carries around a bottle of octane booster, for if he's ever stuck with only 91/95 at a station. Obviously you don't want to do it for long, but as long as the knock is minimal you'll be fine.

Brand wise, they all use the same refineries so really doesn't matter.

98 RON fuel is 98 RON fuel regardless, it is refined to the same standards, so there should be no difference in mixing between brands.

It is generally only bad batches that cause inconsistencies in quality, or if your unfortunate enough to go to a station that has its tanks quite low then you may find minor issues in fuel consumption and power to an extent, but usually not to the extent that it can be noticed from a drivers point of view - maybe only a hand controller or similar showing slightly higher/lower knock readings.

Massive (unsafe) differences in knock levels can only be down to using a lower rated fuel ie: 95/93/91, or an EXTREMELY bad batch of 98, which would be rare.

Further to knock levels and such, as a car gets older especially if it gets out of tune, you might need to increase the octane of the fuel. For example 93 to 95, or 95 to 98. Not so applicable to Skylines, but other 'sports' cars have this problem. Anyway, a good $200 tune should fix that, but just bear in mind you can't always use the fuel in the manual/theory, as reality is different.

personally I have had my car tuned on vpower with a result of 267rwkw and then 278rwkw on the same dyno (different day, however the higher power figure was on a MUCH hotter day)

I only run my cars on ultimate or (manildra e85), and was driving my mates 34 the other day and needed to fill up, the only BP around was closed so I was forced to go to shell. as soon as I left the station the engine check light was flashing under high load.

I have also heard that vpower is a 95 octane fuel with an octane booster to acheive 98ron whereas ultimate is refined as a 98ron

also i know of a few tuners that net lower power figures on shell "fuel" when compared to ultimate.

i dont't have any concrete evidence to back up ANY of these claims, but take it how you want ;)

i do NOT use shell

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...