Jump to content
SAU Community

Recommended Posts

Hey everybody!

Was just wandering how far is far enough to push your stock skyline before you begin to do any damage.

For example how far up the rev line is the furthest to go and how long can you hold it there.

Also what factors you take into account such as; intervals to do it within, temperature of the engine and so on.

I have heard from people its bad to put ur foot straight onto the floor, can this be justified by anyone or is it ok to do it once in a while?

Just looking for some opinions i'm sure some of you will have different views.. Please share :P

Edited by MP_R33
Link to comment
https://www.sau.com.au/forums/topic/242976-pusing-your-car-to-its-limits/
Share on other sites

If your going to be running lots of trackdays look into your under bonnet temps, as i just found out by melting my coils and cracking plugs from heat. Am now looking for some method of venting. Apart from that, your rev limiter should stop you doing too much damage (thats what its for) so high revs arent too bad as long as you dont hold it too long.

Thanks for your input, yer i had assumed it would be fine as long as it is not held there for an extended period of time.

What about the foot flat to the floor is that bad to do??

I have heard from many that it is but in my opinion i dont really think it is... THen again what do i know lol

...theres nothing wrong about putting your foot to the floor, apart from the excessive speed.

also if you bounce it off the limiter too long, your valves might not like it

and from your other thread, leave overdrive off when towing. which i doubt youll be doing in a skyline.

i dont see any way that it could be harmful for the gearbox.

preference i suppose

...theres nothing wrong about putting your foot to the floor, apart from the excessive speed.

also if you bounce it off the limiter too long, your valves might not like it

and from your other thread, leave overdrive off when towing. which i doubt youll be doing in a skyline.

i dont see any way that it could be harmful for the gearbox.

preference i suppose

Yer i thought so it doesnt really make sense for it to do any damage the only difference is increased speed!

As for the overdrive like i said just opinions i heard

- "well Nizmo,

my dads a mechanic and him and his boss told me that the overdrive switch is only meant to be used above 70 km's/h and that having it on while drivin on normal ctreets could cause damage, because it forces the engine to stay in third gear instead to changin to fourth and reving lower."

Thats from an old thread i dug up lol must just be different people i guess

Most engines are pushed for long periods eg. fords xr4 engine was left at redline for weeks and weeks and so was mercedes benz c-class engines; im talking non-stop on a dyno with an unlimited fuel supply.

if your car is tuned well without knock and you dont over-rev your engine can take all the punishment it wants; only reason why most engines blow is while drifting because of the constant lack of airflow and bouncing off the limiter.

Either that or burnouts where the engine overheats very quickly.

I drive hard alot now but i never rev past 7200rpmish and never flat-shift; always nice easy changes to save the gearbox and motor.

Yer i thought so it doesnt really make sense for it to do any damage the only difference is increased speed!

As for the overdrive like i said just opinions i heard

- "well Nizmo,

my dads a mechanic and him and his boss told me that the overdrive switch is only meant to be used above 70 km's/h and that having it on while drivin on normal ctreets could cause damage, because it forces the engine to stay in third gear instead to changin to fourth and reving lower."

Thats from an old thread i dug up lol must just be different people i guess

The above looks a little confusing - when I say leave it on all the time I mean leave the overdrive in the "on" position (i.e. do not use the button to switch it off) except when going down hill while towing or thrashing it through a windy section of road when you want it to hold 3rd.

Don't be too worried, past owner of your car in Japan probley thrashed abit anyway.

You can still do damage to the car even if its stock. Its how you treat your car.

Just do your regular oil top ups and 5000k's oil and oil filter change and check all your fluids too.

Give it abit of stick occationaly but no need to red line it every gear change.

Hey everybody!

Was just wandering how far is far enough to push your stock skyline before you begin to do any damage.

For example how far up the rev line is the furthest to go and how long can you hold it there.

Also what factors you take into account such as; intervals to do it within, temperature of the engine and so on.

I have heard from people its bad to put ur foot straight onto the floor, can this be justified by anyone or is it ok to do it once in a while?

Just looking for some opinions i'm sure some of you will have different views.. Please share :ninja:

Always play it safe unless you have deep pockets and like having your car off the road. There is no hard and fast rule for how hard and how long you can push an engine. The rev limiter is to prevent catastrophic failure and excessive wear but hitting it constantly will see your engine life shortened dramatically. You're not making power that high in the rev range anyway, check figures on peak power and torque, they're not at 7000 rpm so why bother.

Don't boost the car or rev it hard or put it under high load( low speeds and high gears etc) until it's warm, the easiest way to warm it up is drive it gently until the temp comes up, not by sitting in your garage idling for long periods, this will only heat up the water and oil but the gearbox/diff, rotating assemblies etc.

Putting your foot flat to the floor is fine once the car is fully warmed up but again, be mindful of the rev's as excessive rev's will cause excessive damage it's that simple. If I remember correctly, the redline on an R33 is 7000, for me that meant my Series II rarely seen above 6500 or so but that's personal preference. Yes I hit the limiter a few times but it was on rare occasions and my car still had even compression when I sold it after 2yrs of owning it, same goes for my GT-R, it rarely seen anything above 7500 rpm as it went red at 8000.

The harder you drive it, the faster it will wear out. You can't avoid an engine wearing out but you can prolong the inevitable while still having fun.

It's also important to keep on top of basic servicing. Oil, oil filter, air filter and spark plugs go a long way. I chose to replace the oil and oil filter every 5000k's. The air filter was a re-usable type so it was washed and cleaned at the same time and the spark plugs were iridium so were checked and replaced as necessary. You don't have to spend a shit load on oil on a low power car or one that is receiving new oil and filter every 5000 k's.

Enjoy your car and remember to keep the race driving for the track.

Cheers

i kept my tune conservative (probably 10-15 rwkw from what i could have grabbed) and i smash the limiter and flatshift reasonably often.. (usually on low boost of 245 @ 1 bar tho). i understand the risks, but i bought the car to DRIVE!

i'm 6 months in to 265rwkw on an internally standard 25 and no probs so far :ninja:

Hah, I had a Celica back in the day too and gave it a very hard time, didn't die.

I'm not saying Skylines are like glass I'm just saying that I preferred to be kind to mine 95% of the time and that there are some things you should avoid doing all day every day and when cold if you want your engine/turbo gearbox/clutch etc to live longer.

i kept my tune conservative (probably 10-15 rwkw from what i could have grabbed) and i smash the limiter and flatshift reasonably often.. (usually on low boost of 245 @ 1 bar tho). i understand the risks, but i bought the car to DRIVE!

i'm 6 months in to 265rwkw on an internally standard 25 and no probs so far :P

Haha yea my old car was bullet proof. On standard internals (that i know of, it had a rebuild but didnt know what was in there) 250rwkw all day. Only problem was it didnt have a rev limiter. Cant count how many times that car saw 8500-9000rpm and it still went strong, of course these high revs were by accidents in 1st gear as first gear is over in a flash.

now why would you ever own a car that isn't japanese.

motors have the numbers on them a reason, to be revved to.

clutches are pretty much consumables if you have enough power and see a few track days and other things i won't mention.

having 5SFE in my celica, that's not a worry lol.

I do my oil changes every 2000kms now just to be sure lolz.

but i also watch my oil and water temperature gauges; I have a red flash when i exceed 89degree oil temps and 88degree water temps.

Skylines are notorious for breaking 3rd gear under a flat shift and big power/torque so keep that in mind when your shifting.

I do my oil changes every 2000kms now just to be sure lolz.

but i also watch my oil and water temperature gauges; I have a red flash when i exceed 89degree oil temps and 88degree water temps.

Skylines are notorious for breaking 3rd gear under a flat shift and big power/torque so keep that in mind when your shifting.

2000kms is a bit extreme lol, 3500 is really if you want to be on the safe side i say.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...