Jump to content
SAU Community

Recommended Posts

last week I had my car on the CRD dyno and they didn't strap it down,

saying there was no need. Is that normal? & if a car is strapped down

does it change the result & by how much?

last question: if a shop does a before and after run to show you how awesome

their tune is, how can you know whether the before was fair dinkum? is it

too cynical to think such things?

is CRD a "friendly" dyno?

Link to comment
https://www.sau.com.au/forums/topic/245618-dynos-straps-and-friendliness/
Share on other sites

Pretty normal, mine was never strapped with over 300rwkw

strapping does alter thing im lead to believe, how much or whatever is debatable

As for results - You compare to other peoples.

You should really know what ballpark your going to get if you search around. Most combinations have been done before, or with a bit of lateral thought you can bridge across and work it out. So as long as you fall into the area then thats about it.

Obviously if you make 300rwkw on the stock turbos @ 1bar, then thats not right.

But if you say make around 240-260rwkw @ 1bar... then thats about right. More about AFR's, midrange and that kinda thing

Pretty normal, mine was never strapped with over 300rwkw

strapping does alter thing im lead to believe, how much or whatever is debatable

As for results - You compare to other peoples.

You should really know what ballpark your going to get if you search around. Most combinations have been done before, or with a bit of lateral thought you can bridge across and work it out. So as long as you fall into the area then thats about it.

Obviously if you make 300rwkw on the stock turbos @ 1bar, then thats not right.

But if you say make around 240-260rwkw @ 1bar... then thats about right. More about AFR's, midrange and that kinda thing

not strapped at over 300 kws? eeeek

mine squirms a fair bit with straps, i would hate to imagine just wheel chocks.

sounds to me like a visit thru the dyno wall would be inevitable.

and old mates car made 360 rwkws while strapped down, we then took the straps off so it was actually just chained from going forward to far. this aloud it to get up on top of the rollers, first run it went to 385 rwkws.

we then all jumped in the boot, and the next run managed 404 rwkws.

no settings were changed just 3 runs one after the other.

but to the the original question, yea the dyno operator can do the initial run at 3/4 throttle to show how crap its running, and power is down.

they then root around looking at settings in your hc for a minute or two and then do a second run at full throttle. bang 30 kw gain. that'l be $300 thanks.

so yes there are bad operators out there.

but i highly doubt crd would be one of them.

An experienced operator will make a judgment call on whether or not a particular car needs to be strapped down. Don't stress.

It's usually the cars that come on like a bomb that need to be strapped down.

Pretty normal, mine was never strapped with over 300rwkw

You're crazy right?

My car lifts even with straps front and back - there is no way in hell I'd let it go on a dyno without a minimum of rear straps! Not just to protect the car but also the people in front of it!!!

You're crazy right?

My car lifts even with straps front and back - there is no way in hell I'd let it go on a dyno without a minimum of rear straps! Not just to protect the car but also the people in front of it!!!

Dude, there should never be people in front of any car on any dyno!

An experienced operator will make a judgment call on whether or not a particular car needs to be strapped down. Don't stress.

It's usually the cars that come on like a bomb that need to be strapped down.

Spot on :P

Dude, there should never be people in front of any car on any dyno!

Agreed... but try putting this into practice at a Dyno Day or something... Public Liability nightmare if the cars aren't strapped down.

yes not strapping it down can show a higher result - the higher the car climbs on the rollers the higher the power figure. until it falls off and kills everyone of course.

and yes there are plenty of simple ways to make a car look crap for a before run. do you have both before and after runs with all of the parameters printed on them? even then there are simple changes on the car light retarding the timing a little or even just letting it run when it is already hot that would make a difference

and finally, unless the ECU was editted/tuned, the boost was turned up or there was a problem fixed, there would be very little difference in before/after kws.

yes not strapping it down can show a higher result - the higher the car climbs on the rollers the higher the power figure. until it falls off and kills everyone of course.

and yes there are plenty of simple ways to make a car look crap for a before run. do you have both before and after runs with all of the parameters printed on them? even then there are simple changes on the car light retarding the timing a little or even just letting it run when it is already hot that would make a difference

and finally, unless the ECU was editted/tuned, the boost was turned up or there was a problem fixed, there would be very little difference in before/after kws.

How does how high the car is on the front roller change the power output read?

Edited by GTR1993

i had mine at crd with no straps made 304kw atw ,then i went to a dyno day about 3 weeks ago and the car was straped down and made 309kw atw..... the only thing that was diffrent was the knock level was higher when straped and no knock on the street or crd dyno.

How does how high the car is on the front roller change the power output read?

heavily strapped you'll see cars sit on the two rollers, no straps the car will ride up on the front roller

less resitance = more power (in theory)

I might have to get strap/no strap tested next service to see :blink:

I know that, but the way it was written it was talking the higher it climbs on the front roller the higher the number. I dont see any reason for the car to be on the rear roller as its not knurled, and furthermore is free spinning so not needed to read power.

yes not strapping it down can show a higher result - the higher the car climbs on the rollers the higher the power figure. until it falls off and kills everyone of course.

and yes there are plenty of simple ways to make a car look crap for a before run. do you have both before and after runs with all of the parameters printed on them? even then there are simple changes on the car light retarding the timing a little or even just letting it run when it is already hot that would make a difference

and finally, unless the ECU was editted/tuned, the boost was turned up or there was a problem fixed, there would be very little difference in before/after kws.

correct an untied car gives a more accurate reading than one strapped down, the tighter the strapping generally the lower the reading. a properly strapped car will move forward onto the front roller without being bogged down between both.... ie over tight

Edited by URAS

UUUmmm, they strapped mine down hard, then actually checked and retightened the straps because of what they thought was wheel spin - 280rwkw, Yohohama AVs102's 255x 40's on 17" with good tread. So if they hadn't strapped it down it would have gotten bigger numbers? I might have cracked 281..... I assumed they new what they were talking about. What does wheel spin look like on a run anyway - not uncontrolled spin, but partial/light spin?

Not really bothered by it, the tune is the important thing.

the higher the car is on the roller the more weight is distributed onto the roller.

if its at about 60% almost half the rear of the cars weight is not pushing onto the roller.

therfore some sort of wheel spin is likely.

if its on top of the roller then 100 % of the rear weight is transferred onto the roller.

If it is strapped down from infront of the diff using the eyelets in front of the roller, then over the diff under the bar (the DD setup they use) as the car moves foward it is forced harder and harder into the roller as the strap acts as a type of wedge. Seems like a smart idea as the more power it makes, the more it wants to climb up but the harder its held in by the strap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
×
×
  • Create New...