Jump to content
SAU Community

Recommended Posts

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

No pics yet . Rego'd and definitely roadworthy.

I'm waiting on some money to clear from the bank (check deposit from another car sale... Could take another two days).

Plus another two guys were looking at it for the same reason and they are dead keen. It could still fall through if one of the other blokes gets in first.

Fingers crossed the money will clear and I get there first.

Well I did some digging around on its history. Need some second opinions.

Has a new head on the CA18DET. The old one broke a timing belt and destroyed a pair of valves plus other damage. Has a new head with lower k's than the original head plus a new head gasket.

Has a new diff plus a few other bits and pieces. As I mentioned before it still needs a new front bumper.

This all said the bloke will part with it for $5000.

I'm not so sure now. Seems like it has had a tough life... That also said replacing the CA18 is damn easy (comparatively) and I know of three nice cheap (relatively) replacements off the top of my head.

Would anyone else be put off by the way it lost a timing belt and lost a head?

When the new head went on, did they fix or replace anything else?

What caused the timing belt to go?

Any proof, like receipts for the fix?

I'd certainly look into it more, which you by the sounds of it!

excellent mate, well done, seeme that you are not kidding yourself by thinking it wont cost you more money. dont be too worried about the timing belt issue, it happens, and as long as it was repaired correctly it will be fine, but keep in mind the age and milage of these engines. might be worth a sr20 later on down the track.

Well I am about to buy a manual S13 complete with CA18DET, a tad dirty and in need of a new front bar and some lovin' but mechanically spot on (and all stock bar a pod filter) with coilovers and new DBA gold slotted rotors. Desperately in need of some better tyres though.

In response to some people here. I am not going to be competitive in any way (at least not yet). This is a learning and fun experience.

I am not too fond of go karting no matter how fun it is - I have had a bit to do with go karts in the past. I prefer the full sized car. I don't care if I will be ridiculously slow. To restate what I said earlier I just want to have fun.

The ten thousand is my initial budget - car, basic modifications, etc. I suspect I will see this balloon out to at least double this by the end of the year. Lets not get confused between a someone wanting to build a cheap, fun car to take to club days and someone who wants to be leading the field.

When the new head went on, did they fix or replace anything else?

What caused the timing belt to go?

Any proof, like receipts for the fix?

I'd certainly look into it more, which you by the sounds of it!

The timing belt snapped due to age I believe.

Well it seems the repair was done by a competent mechanic (as in a good mechanic but wouldn't take it to him myself) and included a head gasket and a low kilometre head replete with stock valves, cams, etc.

There is definite proof - it drives very well, blows no smoke, came on boost cleanly with no surges/spikes of any kind.

I don't know it just turns me off having found the car and then finding it has had major problems in the past but what would you expect for a 19 year old car that has probably been driven every day of its life and driven hard?

Its still cheap no matter how I look at it. I am paranoid of bottom end damage though even though it all looks fine. Its just the risk of something being sh!te thats turning me off....

Maybe I should just keep looking around. Maybe I should just buy it and if something screws up stick to my guns and build a strong SR20/CA18/RB20 to replace it.

Sounds like a decent choice you've made their mate. Personally I'd go for an SR, but that's just me.

Have you looked into ex-drift cars? Sometimes you can pick up half decent ones with some work done for not much money, just require a fair bit of tidying up from some dodgy modifications.

Well i am always looking around and if its a CA18DET powered S13 which needs bumper and bodywork and is very std then i would nto be too fussed if you miss it at $5,0000 as i believe you will be able to get better examples for that sort of money

Try finding one in tasmania though. Car prices here are ridiculous sometimes - in particular for imports. :)

If you can find a similar car in similar condition either in the state or in a position to be transported here at low cost (aka spirit of tasmania), let me know!

I haven't parted with any cash yet, still waiting on that cheque to clear, and if something better came up I would give the bloke my apologies and snap that up instead.

my only advice would be try not to build a track/street car. i started out doing that with my skyline and it does not work. no track car is fun on the street, and when it comes time to move on it sad to see what people are willing to pay for it :down:

thats why im keeping mine and focusing more on track time

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Need to see other side of PCB in that area...ie; I don't see any thru-hole mounting, just soldered vias (smd zeners in SOT23 have 3 legs but only 2 are used, as reflected by PCB tracks)
    • 4 to 5 is fine. It will be slow, but that's better than blowing turbos. I don't have a PS pump idle up solenoid on my car, because... I think when we put the Neo in we retained my R32 lines. But.... From inspecton of the R34 vacuum hose diagram, you can see that the solenoid needs to be connected to the turbo inlet as source of clean air) and the plenum (as source of vacuum - which is the place for the air to flow to to cause the idle to increase). So 3 to 1 is VERY WRONG. 3 should go to either the turbo inlet, or the plenum. Follow the other hose from the PS solenoid and if it goes to the plenum, then your 3 goes to 2 2 would also serve as a bleed port for a boost solenoid.
    • Pull them out and pull more apart. You can't do shit with them still bolted to the floor of the car.
    • Yes it is. ZD1 is on the other side of the board. Where ZD1 is marked is clearly opposite a 2 pin device. Our 3 pin device here is not a ZD.
    • Alright, a little update on this... I called Fulcrum, who used to be the distributor in Australia. No Bueno, they don't service them anymore.  Called shock works, who don't service them but offered to dyno the shocks for performance, and suggested DNA in Sydney might service them.  Called DNA, who also do not service them and basically said they try to steer customers away from tein for this exact reason these days- there is just no support for them anymore apparently.  Both SW and DNA said they are a not necessarily a bad product, but they just don't service the brand or know anyone who does service the brand anymore.  So... I could keep calling around but at this point I think I'll probably just spring for the shockworks product, unless anyone here knows anything.  Cheers 🍻 
×
×
  • Create New...