Jump to content
SAU Community

Recommended Posts

I've been recently reading up on the differences of between turbochargers and superchargers - interesting read I must say ;)

Now this question occurred in my mind:

Is it possible to stick both a turbocharger and supercharger into a twin turbo car (let say an R32 GTR 'cause I love them)?

If it were possible what would the benefits be?

Seeing as there would be turbo lag, would the installed supercharger cover for that initially (and once it kicks in, ;))?

Sorry, if a similar question was posted. I was too intrigued my hand couldn't stop typing :D

Thanks in advance.

Link to comment
https://www.sau.com.au/forums/topic/258601-two-kinds-of-turbo/
Share on other sites

stockymystock has an rb30 turbocharged and superchareged

can be done, costs lots of $$$, lots of custom work and changes

twin turbo is easier, cheaper, more normal

a good twin turbo setup would negate the require for super & turbo

as it would provide good average power, remember superchargers suck some power to give some power

its not like its free

sure a supercharger needs crank hp to run, but since it creates boost as soon as it starts turning, and feeds it straight back into the engine to create more power, the hp needed to run the sc is then accounted for. feedback cycle.

eg. engine 100hp

sc 50hp

sc boost power gain 100hp

total hp when you use the engine with sc = 100 - 50 + 100 = 150hp. net increase in power even though the sc takes 50hp, it gives back more almost immediately.

the energy is supplied by the additional fuel burnt as a result of the increased intake charge pressure. you wont experience any 'lag' from a supercharger

the power is not free, you pay for it in fuel. but you dont 'lose' any power from having a sc

if you can do fab work yourself and have the mechanical knowledge, it can be a cost effective option

of course it takes a specific application to require a super/turbo combination.

in track, drag, or most race applications, low end driveablity and torque down low is not usually a factor as gearing and driver skill is used to keep the revs in the powerband (top end of the rev range).

twincharging can be done relatively cheaply using aftermarket parts such as toyota factory superchargers.

unless you want something different there is probably an easier solution to lack of low end torque with a large turbo.

i would suggest a good ecu setup with anti-lag and the use of cheap t3/t4 based turbo chargers (as you'll probably have to replace it once in a while depending on your use of the anti lag).

or nitrous

Is it possible to stick both a turbocharger and supercharger into a twin turbo car (let say an R32 GTR 'cause I love them)?

Sure. There are a couple of aftermarket cars that have been twincharged, and Volkswagen has a production one.

Benefits are no lag at low RPM while getting more power down low thanks to the supercharger, and at high RPM you can enjoy the better efficiencies of a turbocharger.

The problem is getting it all to work together smoothly.

try looking at the twincharged s15 on youtube; was a fantastic watch and the results were fantastic.

sr20 yes but there was almost no lag so on an rb26 i doubt there would be any

are there any superchargers that disengage at a certain rpm???

So do turbochargers.

Technically yes, but in practice: they're sucking energy from waste gasses that are just being ejected out of the car anyway.

They do cause restriction, yes. but they don't suck raw shaft engine power

I believe the superchargers on the 4agze does that.It has a clutch on the blower drive much like an ac clutch

Yep.

I'm pretty sure the supercharged Merc engines have them as well.

They do cause restriction, yes. but they don't suck raw shaft engine power

And that restriction causes pumping losses. Stick a restriction in your exhaust, and see what happens to your power output. It's irrelevant whether that power "loss" has come from something attached to the crank, or something stuck in the exhaust. A power drop caused by an induction charger is still a power drop.

Its misleading to say superchargers "draw power to make power" as a pro against turbochargers, because the latter does the exact same thing.

Turbochargers are more efficient because they draw less power to give the same gain, but its not the free lunch some people make it out to be.

Edited by scathing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...