Jump to content
SAU Community

Recommended Posts

Hi Everyone,

Not sure if this has been covered before, but it has been on my mind recently, so I thought that I would draw from the wisdom of SAU....

From what I understand, when comparing the RB25DET (R33) and NEO (R34), the NEO engine makes 206kw (stock), compared to RB25’s184kw (stock) - why / how does the R34 make more power?

From what I understand the R34 has a bigger SMIC, different turbo, different engine management - not sure about injectors etc.

But if you were to get an RB25DET and a NEO side-by-side and say stick the following on both engines:

Apexi PFC

Pod Filter

FMIC

Turbo

Fuel Pump

Bigger fuel injectors

and then tune them the same, would they then both then make around the same power - (bringing the RB25DET upto the NEO level) or are their more internal mechanical differences that I am not aware of?

Look forward to your responses!

Thanks,

Peter

Edited by Peter
  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

adding those mods to them will multiply the difference between them . its differences like nvcs is continusly variable as opposed to on/off. begger exhaust valves . solid lifters/diff cams . and 5 years further electronic development

Overall even with the parts - the limit factor is boost/airflow.

The GT-t turbo is marginaly bigger than the GTS-t turbo, so you get ~10-15rwkw more... but thats it if you do 'every' basic mod short of changing the turbo itself.

Equally sized turbos (upgraded) i would expect very little difference overall. Happy to be proven wrong but i dont think the gains would be anything major over either motor once you start talking boost

From what I've seen the majority of it is the extra boost they run, and of course the supporting mods to allow it to do so safely (bigger turbine a/r, intercooler...).

Whenever we dyno'd them with intake, exhaust, fmic and say 10-11psi they always seemed to make similar power. The only R34 I know of which has dynod on the same dyno as my car was tuned on with upgraded turbo etc was only running a T3/T4 and made a fair bit less power.

Isnt there a bit more compression in the NEO too?

Its pretty clear, if you start with more power stock, and add parts you will surely end up with more power.

Yes, but if when adding more parts your replacing what it was that made the NEO more powerful in the first place, then you wouldn't get the difference. Guess it depends on turbos.

We are talking about RB25 Vs RB25neo, not r33 Vs R34.

So keeping that in mind we are comparing the performance of the engines not the cars.

higher lift cams and diferant cam timing. better intercooler and bigger turbo and higher comp ratio
adding those mods to them will multiply the difference between them . its differences like nvcs is continusly variable as opposed to on/off. bigger exhaust valves . solid lifters/diff cams . and 5 years further electronic development
So do people really think all the above enhancements don't improve the performance? :(

I had a high flow rb25 turbo (with the VG30 ext housing) and my r33 rb25, with tomei poncams and extensive race head porting, managed to produce a respectable 268rwkw. When i upgraded to the GTRS turbo, i sold the high flow to a mate with an r34. The 100% stock/unopened neo engine made 273rwkw using the same turbo on the same dyno.

In other words; i had to spend over $2k to achieve the same results as a std rb25neo.

I had a high flow rb25 turbo (with the VG30 ext housing) and my r33 rb25, with tomei poncams and extensive race head porting, managed to produce a respectable 268rwkw. When i upgraded to the GTRS turbo, i sold the high flow to a mate with an r34. The 100% stock/unopened neo engine made 273rwkw using the same turbo on the same dyno.

In other words; i had to spend over $2k to achieve the same results as a std rb25neo.

Did you get any before and after cams and race porting dyno plots?

So do people really think all the above enhancements don't improve the performance? :(

I had a high flow rb25 turbo (with the VG30 ext housing) and my r33 rb25, with tomei poncams and extensive race head porting, managed to produce a respectable 268rwkw. When i upgraded to the GTRS turbo, i sold the high flow to a mate with an r34. The 100% stock/unopened neo engine made 273rwkw using the same turbo on the same dyno.

In other words; i had to spend over $2k to achieve the same results as a std rb25neo.

They might, but very minor at best.

The cams is nothing major, the timing is overidden by aftermarket ECU's, and a comp ratio increase (again minor) isnt going to instantly give you massive gains. Depending on circumstance/boost it might even hold you back.

Its all done in the form for a stock motor, to meet emissions. Once you really start playing most of it goes out the window when (probably) 1psi negates all those changes.

As Lith said - did you get a before/after the porting? If you didn't, very hard to tell to the point of really showing not a lot.

When you think i made 270rwkw stock head, then over 370rwkw on 104 fuel (and could have made more) again with a stock head (Non-neo)... Guilt-Toy has made 370rwkw Non-NEO head also with response to make you drool...

I don't think your one isolated example is that accurate in this instance and there is much more at play there to be able to simply say you spent 2k and couldn't beat a NEO.

I've seen no result here to date that says NEO RB25 heads give leaps and bounds gains like you are talking.

Could be all your porting was putting the turbo out of efficiency, and so the list could go on :cheers:

Overall even with the parts - the limit factor is boost/airflow.

The GT-t turbo is marginaly bigger than the GTS-t turbo, so you get ~10-15rwkw more... but thats it if you do 'every' basic mod short of changing the turbo itself.

Equally sized turbos (upgraded) i would expect very little difference overall. Happy to be proven wrong but i dont think the gains would be anything major over either motor once you start talking boost

to throw in another viewpoint......

IMHO you are exactly right ash...

bombtrack and i both have unopened 25's with HKS 2835 pro s turbo's, only mine is a 33 and his a 34

with stock turbo's chris's was a tiny bit more responsive than mine, and made 5odd rwkw more top end

now with the same setup (pretty much) they have leveled out.

on pulp i have 270rwkw running 18psi and he has 275rwkw running 18psi...

the only difference is cams... mine are stock, his tomei drop in items...

same tuner, same dyno, no major weather differences on the tuning days.

i get better transient response, but not heaps, <500rpm and he gets 5rwkw top end.

Contrary to populart belief, Neo NVCS is also just on and off. NOT continuously variable. It just turns it on and off more than once through the rev range.

Neo has superior heads, slightly larger turbine for higher flow, different stock cams.

Also has different rods and crank but neither of these are performance adders, just reliability. Maybe lighter weight for better revving.

Neo also has an engine cover. It looks better.

nu-ah... the engine cover looks teh ghey....

there have been studies done... facts found... scientists, test tubes, lab coats, bunsen burners, calculators etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I had 3 counts over the last couple of weeks once where i got stranded at a jdm paint yard booking in some work. 2nd time was moving the car into the drive way for the inspection and the 3rd was during the inspection for the co2 leak test. Fix: 1st, car off for a hour and half disconnected battery 10mins 4th try car started 2nd, 5th try started 3rd, countless time starting disconnected battery dude was under the hood listening to the starting sequence fuel pump ect.   
    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...