Jump to content
SAU Community

Recommended Posts

The ATR43SS-1 PU version is installed this morning. I only took it for a test drive based on my old tune. It feels like a huge turbo with babe turbo's response. Its got this really big pull under throttle, I haven't give it much yet, but very new driving experience, will have a interesting result soon.

I'm not sure what the dyno says yet. Feels like a 3540 comes in full boost at 3000rpms. Its got a crazy pull when you give to it. Compare to SS1 it feels like it has pickedup heaps more torque through out rev range with similar sort of response. But once again the tune in it now is for a much larger turbo so not sure what it feels like once its fully tuned. Will post up results.

Add:

Went for a 50kms drive, and its got even more responsive (probably got all the thick stabilizing oil washed away). Heaps of torque and zappy response. The best way describing it taking off would be: like a billet leaving the gun barrel. The car just launches, there is not a bit of flat spot down low or any where in the rev range.

As turbo builder I'm very happy with the way how it delivered power and torque. The drivability and performance worth every hour spent designing and making it.

Whats happening with this Turbo? Still in testing phase or?

Made a bigger housing for it this weekend. The test car's currently got a G1 on it, need to test that first. will swap it over when I have a chance.

Stao seeing as you have access to original garrett parts, have you considered using an OEM 2871 52t CHRA and making a mock GTRS for customers to buy?

You clearly have the ability to turn .64 T28 housings into T3 skyline specific housings and your .60 compressor looks very similar to the T04B found on garrets, maybe you could port shroud this and make one up?

Could become a hot seller.... Save lots of cash on buying HKS, who would say no?

NS111 turbine, .64ar turbine housing, GT35 71mm 52 trim compressor, .60ar compressor cover.

At the kind of cost that would involve, and if we were going to talk hypothetical things we'd like to try... I'd consider a DBB T3/T4E 50-trim CHRA to be a combination almost worth shoving into a bolton solution if .63a/r hot sides, big torque and spool and respectable power are your thing. Some might balk at the idea of going a t3/t4, but ancient Mitsi truck turbos are cool right? ;)

At the kind of cost that would involve, and if we were going to talk hypothetical things we'd like to try... I'd consider a DBB T3/T4E 50-trim CHRA to be a combination almost worth shoving into a bolton solution if .63a/r hot sides, big torque and spool and respectable power are your thing. Some might balk at the idea of going a t3/t4, but ancient Mitsi truck turbos are cool right? ;)

How would that involve some sort of elevated cost? Stao is custom machining wheels from scratch (far more labour intensive than a prefabed CHRA) and his housings are already what I have described..

Same same but different, hell I'd even buy it in a generic CHRA as long as the specs are what ive asked for. GTRS bolton for Garrett T2 price, yes please?

Or maybe your just cranky I sold the 33 ;) Dont worry man, JZ is still in the garage with its nissan specific mounts attached.

Lol funny, no actually I forgot (or didn't know?) that. I was just saying a combo I think may also be interesting with similar cost and effort.

Lol need a catch up I see, I havent been on MSN again coz my landlords turned into a prick. Ill be back online soon and well chat. Have acquired an S14 I had a heavy hand in building many years back.

As for the said recommendation, what about that old tech TR30R we talked about :P Dont you want to see that back into production? Old school rally tech at its best (or is this one in the same)

Stao, get busy!

Stao seeing as you have access to original garrett parts, have you considered using an OEM 2871 52t CHRA and making a mock GTRS for customers to buy?

You clearly have the ability to turn .64 T28 housings into T3 skyline specific housings and your .60 compressor looks very similar to the T04B found on garrets, maybe you could port shroud this and make one up?

Could become a hot seller.... Save lots of cash on buying HKS, who would say no?

I can make them that way if any one wants one, but not really interested in building and selling them as a product as the SS-1 has out performed above in pretty much all accounts.

Here are some results form the ATR43G1 unit. The peak was 232.9rwkws at 18psi. Turbo makes 20psi by 3000RPM. It has dropped to about 14psi up top, that’s because the comp wheel isn’t big enough to keep up with the flow up. That is the behavior of this turbo.

atr43g1233rwkw.jpg

atr43g1233rwkwboost.jpg

On the road it is super fast and responsive. This turbo is good for some one who's looking for 200~230rwkws running on stock injectors and AFM. This turbo should also be excellent on Rb20dets.

Well there you have it. If I had a skyline all over, it would be running the G1. A good tune on stock injectors and afm with a sturdy FPR and pump would be awesome. Budget killer all over!

Thats awesome Stao, thanks for going to the effort to build and test one for us all.

Well there you have it. If I had a skyline all over, it would be running the G1. A good tune on stock injectors and afm with a sturdy FPR and pump would be awesome. Budget killer all over!

Thats awesome Stao, thanks for going to the effort to build and test one for us all.

+1 Well done Tao!!!! Great budget option

Hey Stao, could you super-impose the G1 performance graph in your earlier radar graph with the 4 other turbos, ss1, ss2, G3 and ss1 MU.

Just get yourself a G1 and a $180 buck front n dump piece from JJR.

Ive got my money on it being a winner.. DO IT.

Here's update with the SS1 PU prototype.

My car's came with an ebay cooler which was getting cooked on the dyno. It maxed 291rwkws (was not complete as cooler pipe slipped) when the cooler is cold and average of 270rwkws when the cooler is hot.

I had 2x actuators today, one is 14psi and the other was high pressure that peaked 25psi. No boost controller was used on those runs. This turbo was not equipped with a gate controller.

9 sec ramp:

power.jpg

boost.jpg

Its pretty happy on the dyno, made power pretty easily, and very good to drive on road. It makes 220rwkws @ 4000RPMs with the best run and 210rwkws @ 4000 on the average run.

Compare to the previous run it have lost 450RPMs making 20psi by 3350RPMs. But picked up lot more mid range and top end, which is pretty worth it. I'm pretty happy with how it overally performed. I will probably going to give it another run with a better cooler.

So it made 260rwkw on 14-15psi, am i reading it right?

Yes that was correct, and it was very quite on the head phone (detonation detector). The engine and turbo were very happy today.

So it made 260rwkw on 14-15psi, am i reading it right?

yeah this second turbo is great i was not a fan of the ss1 as it was too responsive and rolled off way to much, this has the perfect balance and is doing it with easy, no trickery in the housing re boost control etc... exhaust manifold pressure was nice and low.... THIS WOULD BE MY CHOICE as a bolt on for rb25... it literally is making 260 as easy as pie.... would be a nice 22psi turbo for E85 on a stocker 300+ with killer response.

i dont mean to be a great turbo expert but looking back at post #1980 and comparing that to the new graphs

atr43g3 made peak torque of 843nm @ 4100rpm and 291kw atw peak @ 5500rpm 21psi

ss1 pu made peak torque of 540nm @ 3400rpm -4500rpm?? and 290kw atw peak @ 5500rpm 20psi?

is it worth a little better spool compared to the higher torque?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...