Jump to content
SAU Community

Recommended Posts

I just brought a hypergear turbo and i have heard from people they say if you use a 3inch metal intake on the cold side of the turbo it gets the most of the power out of the turbo?

Anyone know anything about this? If so some info would be great and what i need to do it? I think there is a link on the hypergear page if anyone has it could they post it up?

Cheers

Well depends on the turbo. Intake pipe should ideally be the same size as the inlet to the turbo. So if you've got one with a 3" compressor inlet then 3" intake pipe will do, if you've got one with a 4" inlet then ideally a 4" intake pipe would get the best results. Not sure what you're asking for with "what you need"? You need some pipe and some welding skills if you want the PCV and BOV returns?

All been covered in this thread before though.

You can get Scotty or Abe2 to make an induction pipe. check page 264

Or if you have a Adaptronic or a map sensored ecu I would just run a 3inch metal pipe with a 45 degrees silicon hose and a pod.

Check page 89

You probably find all your answers on page one, I've labeled all the important discussion bits in reference and linked to according pages.

Interesting that they didn't use any correction method, I've never had a run on Allstar's dyno without SAE being used.

They only put correction on to make people feel better their car made shit power...

To my understanding that the correction method makes the HP reading true in situations that would alter the output of the actual performance levels. It is calculated based on humility, air density, temperature, and altitude. Without correction the result could significantly differ depending on surrounding environment, but not necessarily only to a more positive or negative extend.

As If I knew the dyno has no corrections then I would want to have my car tuned at night when humility is low. air temp is cold with higher air density. :whistling:

Updates:

I'm getting some steam pipe bolton manifold and high mount manifold made overseas as I'm typing. I should have a prototype received by mid next week for trailing and testing. Those manifolds will be available for $300 to our customers assume they perform as expected.

It appears a larger turbine setups would perform better on factory manifolds, I will trail a SS2 in a .82a rear housing on current std manifold for some comparison.

Checked actuator pre-load which is about 4mm but rod isn't straight so might play with that next days off. The bracket for the actuator is on a very different angle to what is required so need to modify or bend it somehow.

It has to be in a particular angle as else the comp cover will hit the manifold. I've added few spacers under the actuator between the bracket. as long as the rod is perpendicular to actuator it self it will actuate fine.

But the rod isn't perpendicular. When disconnected it sits between the 2 pins. Might try modify it so it doesn't need the washers to space it off the bracket

Rofl. Told you guys, was tied down financially.

spent the majority of my weekend motor swapping 2 s14s, on my own, to fund this. Just so I could say, told you so :P

and I told you guys I make decisions fast once I can afford to :P

Me too! I watched the entire development of the SS1 and SS1PU in this thread, I know the genuine effort that has been put into it and I know what I'm getting.

On my way to the bank now. EDIT: ANZ the lazy pricks don't open till 9:30 so. I'll be paying for my turbo at lunch :P

This will be mega.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah, don't bother doing any actual measurements on the car. Just go ask the inter-f**king-net.
    • I currently have 18 x 9 +30 on the front with 18 x 10.5 +38 on the rear. Absolutely regretted it. Ended up putting 15 mm spacers on front and 25 mm spacers on the rear. Not to mention the rears were like a mm from hitting the coilovers. Definitely would go more aggressive then what you were originally planning. Keep in mind my guards are rolled and cars fair low so you might possibly need to roll guards depending how aggressive you go and how low the car is. Im not an expert but the 18 x 8.5 +25 18x9.5 +30 Sounds like it would sit much better.
    • Hey guys, sorry i have been researching for a few months and absolutely cannot wrap my head around this. I am about to order some rims to fit my R34 Gtt with coilovers My original plan was to order Rota grid R in 18x8.5 +30 235 40 R18 Fronts 18x9.5 +35 255 35 r18 rears But then the thought in my head said this isnt aggressive enough. I want the most concave spokes i can get without too much of poke and scrubbing   So my thoughts now is  18x8.5 +25 18x9.5 +30   My question is will this be the most aggressive i could get it without any guard rolling and does the type of rim style affect the offset / size.   Thanks everyone.
    • Lower parts are there. On passenger seat, bright yellow bit is the release mount. On drivers, bright yellow bit is the lower buckle for the other side. My bet is lowers are tucked out of the way as much as possible for visuals.
    • I'm guessing its a 4 point harness, 3 of the 4 belts are visible. I'm guessing the hidden belt is tucked down between the seat and door. 
×
×
  • Create New...