Jump to content
SAU Community

Recommended Posts

So Superlap has given me renewed vigor to finish this stupid car, I thought I might start a thread about it...

Hopefully it will give me that little bit more encouragement to work on it!

In January 2008, I flew to Perth and bought a 1994 R32 GTR from a forum member. Mostly standard, with dodgy old Tanabe suspension and some beautiful BBS wheels, it provided me with a very clean (actually TOO clean, in hindsight) platform for me to work with...

080114_exterior.jpg

080114_rear.jpg

080114_interior.jpg

080114_engine.jpg

Link to comment
https://www.sau.com.au/forums/topic/263976-merlis-r32-track-bitch/
Share on other sites

  • Replies 615
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Work kicked off in earnest :)

Immaculate R32 GTR was stripped bare...

080217_intstrip.jpg

080421_dashout.jpg

..... and all sound deadening removed (Anyone who does this with a heat gun is a chump - this took about 2 hours ;))

080322_dryice.jpg

I lost the good photos where pieces of tar were coming off in chunks as big as pizzas, but you can see some big pieces in the bucket in this photo:

080322_chunks.jpg

2 hours later, and we have this :P

080322_floor2.jpg

080322_boot.jpg

Here's what was removed in the initial pass with dry ice!

080322_bits1.jpg

080322_bits2.jpg

So it took about 2 hours of dry ice to get it there...

................ and about another 10 hours to get it to this state (and some people call me anal! PFFFFFFT!!! :) )

080421_wiring.jpg

080421_rearint.jpg

Time to clean up under the dash ;)

080421_passenger.jpg

Next, it was time for the roll cage...

Steve from Justjap gave me the intro to Peter Muir from Bond Roll Bars, who's race car time is precious these days since he has landed some lucrative industrial contracts.

I could not have envisaged a better job. I owe Peter a few cases of beer for this.

080613_cage01.jpg

080613_cage02.jpg

080613_cage03.jpg

080613_cage04.jpg

080613_cage05.jpg

080613_cage06.jpg

080613_cage07.jpg

080613_cage08.jpg

080613_cage09.jpg

080613_cage10.jpg

Jesus Christ! You are anal... Hahaha Just kidding, tell you what though merli you are definately a perfectionist. Look at how clean and new that floor is!

Keep it going!

Gimme your brakes... You know I'll look after them ;):P

First pick looks almost the same as my GTR with the track wheels, i dont have the n1 vents though, same white though with same gold bbs lm wheels. looks sexy :P

haha knew it wouldn't be long before you were back into it Andrew!

Looking forward to seeing you out on the track ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...