Jump to content
SAU Community

Recommended Posts

Craig don't you have the Haltech installed? Is it the PS2000?

Had a Haltech Platnum series.....go rid of it a long time ago!

Now have a Nismo piggybacked with and E-Manage Ultimate......I have bugger all low end restrictions with throttle or Cam's......as seen first hand by PN-Mad both in 2WD and 4WD!

Had a Haltech Platnum series.....go rid of it a long time ago!

Now have a Nismo piggybacked with and E-Manage Ultimate......I have bugger all low end restrictions with throttle or Cam's......as seen first hand by PN-Mad both in 2WD and 4WD!

Ahh ok...I think the Etuner's site has your car there listed with haltech....that's why I asked

Had a Haltech Platnum series.....go rid of it a long time ago!

Now have a Nismo piggybacked with and E-Manage Ultimate......I have bugger all low end restrictions with throttle or Cam's......as seen first hand by PN-Mad both in 2WD and 4WD!

i still cant get over this.. mines still yuck on take off lol..

i wanna see it happen in Video form!

I had the Impul on by itself......I also had just put on the suction pipe and the fabricators had not followed my instructions correctly so I had a slight over boosting problem and as the Impul has no restrictions it helped me to melt a cylinder.

Never had a PS2000 on my car!

Ironpaw where is this Etuners site you speak of....I might have to go and update it a little!huh.gif

.....and if I remember correctly OZ is punching bigger numbers than Japan with the E-manage ultimate with a VQ25det!

You don't remember correctly.

450awps (331awkw) has been done in a street registered NM35 in Japan.

Scott isn't there yet... at least not until the new turbo is installed (if it ever fkn arrives!!).

Having said that, all the "big number" NM35's in Japan have had their capacity increased to over 3L.

Much more impressed with the 2.5L numbers Aus is producing!

i still cant get over this.. mines still yuck on take off lol..

i wanna see it happen in Video form!

I need to find someone stupid enough to sit in the car with me and film:P....where Andy when I need him...lol!....I wont do it again until the shift kit goes in either!.....then I might have to do a quarter run!

Edited by Jetwreck

So with the throttle restrictions; can someone with a stock ecu & an informeter tell me what they get as an output from the "Throttle %" if they flatten the accelerator from a stationary position? Does that corroborate the restriction or is it 'futher' along the line?

You don't remember correctly.

450awps (331awkw) has been done in a street registered NM35 in Japan.

Scott isn't there yet... at least not until the new turbo is installed (if it ever fkn arrives!!).

Having said that, all the "big number" NM35's in Japan have had their capacity increased to over 3L.

Much more impressed with the 2.5L numbers Aus is producing!

Scott's will smash that on E85......shit I recon I'll get to that with a shift kit and 100 Octane and 20PSI and no F-Con Pro!

Scott's will smash that on E85......shit I recon I'll get to that with a shift kit and 100 Octane and 20PSI and no F-Con Pro!

Take a breath Craig.

That 450awps was on pump... and yes, I know Scott will smash that power level... and yes I know that with the old turbo, his car had very little lag.

Oh, I should mention that particular car wasn't using the Fcon V-Pro... it was using the iS.

So with the throttle restrictions; can someone with a stock ecu & an informeter tell me what they get as an output from the "Throttle %" if they flatten the accelerator from a stationary position? Does that corroborate the restriction or is it 'futher' along the line?

I ran a cable throttle and still had the same takeoff, the cams go into full retard below 35? Kph to negate the need for traction control and make the car nice and friendly do drive. I will have the stock cam mapping data soon when I install the Vmanage so I will let you know exactly what it does.

Take a breath Craig.

That 450awps was on pump... and yes, I know Scott will smash that power level... and yes I know that with the old turbo, his car had very little lag.

Oh, I should mention that particular car wasn't using the Fcon V-Pro... it was using the iS.

I'm breathing just fine buddy!

Hey did they post up the dyno sheet.....I remember seeing a couple but that was a while ago.......want to compare to Scott's and mine....cannot find in in my J a p browser for some reason!

So what's that advantage of the Fcon units?

Edited by Jetwreck

I ran a cable throttle and still had the same takeoff, the cams go into full retard below 35? Kph to negate the need for traction control and make the car nice and friendly do drive. I will have the stock cam mapping data soon when I install the Vmanage so I will let you know exactly what it does.

DO WANT THIS!!!

hurry up!!! before my reno funds dry up!! :ninja:

No dyno sheet unfortunately.

Both F-con's intercept the signal from the ECU to the engine and modify it as per the tune, but they are quite different.

Fcon iS is pretty much an eManage Ultimate + Vmanage, but with a Video output... and it looks pretty (not that you'd see it :P).

That being that it add's/subtracts to the OEM ECU's signals (timing, fuel etc etc).

The problem with this is that the stock ECU is damn clever and will react to the return signal accordingly.

(ie Ecu sends signal to engine, iS intercepts signal and adds a fixed number of degrees to the timing, signal returns from engine to stock ECU, ECU takes additional timing out to bring it in line with what the stock levels "should" be, iS intercepts and adds it's fixed number again - which is now less due to the reduction in timing in the "send" signal from the ECU).

I guess the trick here is to tune outside of the stock ECU's limits :)

Fcon V-Pro intercepts the OEM ECU signal and completely replaces the them with the "tuned" information, so regardless of what the stock ECU receives and adjusts for in the return signal, the V-Pro dictates the parameters in it's "base" tune to the Engine.

Edited by iamhe77

So with the throttle restrictions; can someone with a stock ecu & an informeter tell me what they get as an output from the "Throttle %" if they flatten the accelerator from a stationary position? Does that corroborate the restriction or is it 'futher' along the line?

I think it is 79%. If no one else weighs in to say differently l can plug it in & do a test. I do know that I can't get above 87%, ever.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
×
×
  • Create New...