Jump to content
SAU Community

Recommended Posts

anyone got these on there car? or similar?

http://www.ebay.com....0#ht_1263wt_984

http://www.ebay.com....c#ht_1075wt_907

just want some feedback......good? bad? noisy? hard to setup?

Apparently these particular ones are not renowned for their sturdy construction.

Check these;

http://www.ebay.com.au/itm/Nissan-STAGEA-M35-SKYLINE-V35-350Z-REAR-TOE-ARMS-/130554820791?pt=AU_Car_Parts_Accessories&hash=item1e65ac78b7

Doesn't appear to have any Front Arms ATM, but he does get them.

I've dealt personally with this trader; (Bought my BC BR's from him) great guy, answered heaps of questions, couldn't do enough to help, and then followed up several weeks later to ensure I was happy. Nuff said.:thumbsup:

what about K sport

BE-0019 Rear Camber Arms (Nissan- S14 . S15 . R33 . C34 . C35 . GTR . Skyline) Pillow Ball

BE-0026 Pillow Ball Rear Traction Rod (Nissan- S14 . S15 . C34 . C35 . R33) Pillow Ball

BE-0029 Rear Traction Rod (Nissan- S13 . S14 . S15 . 300ZX . Z32 . R32 . R33 . 180SX . A31 . C33 . C34 . C35) Pillow Ball

BE-0049 Tie Rod End (Nissan- S13 . S14 . S15 . 300ZX . Z32 . R32 . R33 . 180SX . A31 . C33 . C34 . C35 .) Aluminum / Pillow Ball

BE-0057 Tension Rod (Nissan- S14 . S15 . C34 . C35 . R33 . Z34) Aluminum 6061 / Pillow Ball

I thought those were the ones you had Ryan.

Y u no fit them?:nyaanyaa:

Because I'm a slack bitch!

Nah, I want to get them fitted right before I get a wheel alignment so they can be properly adjusted. And if I wait until I get the BCs, which looks like it will be quite soon because I'm getting really sick of it wallowing, I can get it all aligned in one hit.

Lol all good I know.

Turns in really well now with the strut brace and sway bars, hopefully the shocks fix up the ride. Looking forward to getting the toe arms in there, as it looks like it needs a bit of a camber adjustment on the rear.

Lol all good I know.

Turns in really well now with the strut brace and sway bars, hopefully the shocks fix up the ride. Looking forward to getting the toe arms in there, as it looks like it needs a bit of a camber adjustment on the rear.

Hang on, are you trying to adjust the camber with toe arms?

Edited by slippylotion

what about K sport

BE-0019 Rear Camber Arms (Nissan- S14 . S15 . R33 . C34 . C35 . GTR . Skyline) Pillow Ball

BE-0026 Pillow Ball Rear Traction Rod (Nissan- S14 . S15 . C34 . C35 . R33) Pillow Ball

BE-0029 Rear Traction Rod (Nissan- S13 . S14 . S15 . 300ZX . Z32 . R32 . R33 . 180SX . A31 . C33 . C34 . C35) Pillow Ball

BE-0049 Tie Rod End (Nissan- S13 . S14 . S15 . 300ZX . Z32 . R32 . R33 . 180SX . A31 . C33 . C34 . C35 .) Aluminum / Pillow Ball

BE-0057 Tension Rod (Nissan- S14 . S15 . C34 . C35 . R33 . Z34) Aluminum 6061 / Pillow Ball

Not sure if C35 is the same as M35. Highly doubt it...

not even remotely the same

the S and C and R chassis have a completely different suspension setup to V and M chassis.

i was just thinking they cocked up the letter HAHA

well the kit is apparently the same as the R35 apart from one rear rod is different

anyone thinking of getting the castor/radius arm bushes on their M35 should get it for sure. best drive ive had of my car in a long time. it feels so good on the road now. no creaking and no clunking!

anyone thinking of getting the castor/radius arm bushes on their M35 should get it for sure. best drive ive had of my car in a long time. it feels so good on the road now. no creaking and no clunking!

I know it was probably discussed 6 pages ago in an unrelated thread, but where from & how much?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...