Jump to content
SAU Community

When Parked Neutral Or In Gear ?

cm712
 Share

Parked neutral or in gear?  

52 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

iseekool Veteran

iseekool

Posted
Posted
I personally leave my cans :ninja: in neutral. The only time I leave it in gear is on a steep incline, and that's once in a blue moon.

So the can does not roll down the hill.... haha

When I drive a manual car - i've been told to always leave it in 3rd gear or higher, never knew the real reason for 3rd specifically... but I'm *guessing* if you leave it in first or second and you accidentally crank the engine in gear you could possibly cause the car to literally start moving.

in an auto car - I always put it in park when the car is parked.

GT-5732 Rising Star

GT-5732

Posted
Posted

I think the majority would leave it in Neutral, as most would have a turbo timer installed (on this site). but when i drive a car without i would leave it in reverse as i have heard its the strongest gear.

Humbla Grand Master

Humbla

Posted
Posted
Hay guys me again when ur parked should u leave ur can in gear or in neutral ?

What gear if u should leave ur car in if left in gear ?

What do you do, do u leave ur car in neutral or in gear ?

Thanks for your answers guys

When i was learning to drive many moons ago,like 30 years i was told to park in first gear in a manual and park in auto,don't know if it's right but it's worked for me so far. :ninja:

Kinks Grand Master

Kinks

Posted
Posted
i've been told to always leave it in 3rd gear or higher, never knew the real reason for 3rd specifically... but I'm *guessing* if you leave it in first or second and you accidentally crank the engine in gear you could possibly cause the car to literally start moving.

Probably what some dumbass's logic was, for leaving it in a high gear. You will definitely move if you crank it in a low gear.

The reason for parking it in a low gear ie 1st gear is that 1st provides the greatest resistance to moving. 4th gear will roll freely, 1st will stop a car.

If you're on a really steep hill then reverse is normally a bit shorter still so use it instead.

Personally I always park on flat ground so I leave it in neutral. If I park it on a steep driveway then I leave it in gear.

Mr GTR-32 Community Regular

Mr GTR-32

Posted
Posted

I live down a steep hill and park my cars on the street, i always parked with 1st gear in and it has saved me many times.

I once went to drive to work one morning and obviously didnt pull the handbrake up tight enough jumped in pushed the clutch in and the car started to roll down, HOLY COW 1st gear managed to hold 1.5 ton of car all night from rolling down the hill into one of my neighbours lounge room.

For me now its habit living down a steep hill for the last 20 years and many times this has been the case where the gear saves a handbrake in need of tensioning etc etc.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • GTSBoy
      Blue/grey smoke after idle

      By GTSBoy · Posted

      The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • sunsetR33
      Blue/grey smoke after idle

      By sunsetR33 · Posted

      Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • sunsetR33
      Replacing turbo water line - any recommendations or advice?

      By sunsetR33 · Posted

      One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...