Jump to content
SAU Community

Recommended Posts

To answer some of the various questions:

how you get your hands on one of them?

Sort of one of those things - you either know someone with one who uses it for work or you can't get them.

So what was your conclusion on the fronts?

Too much toe in, camber or presure?

I was pretty happy with the fronts to be honest.

Awesome tool :sick:

So did you get a chance to use it a number of times to see if any adjustment in the susp was helping or was it a once off?

Did you just call me a tool? :):)

Just used it the once (it rained later) to check that the settings were about right. I am reasonably confident they were.

clockwise track? the lefts look really good. right rear pretty good too, though obviously not working as hard overall and right front not bad, but spread is a fair bit wider.

pretty sexy piece of gear. thanks for sharing big fella. :sick:

clockwise track? the lefts look really good. right rear pretty good too, though obviously not working as hard overall and right front not bad, but spread is a fair bit wider.

pretty sexy piece of gear. thanks for sharing big fella. :D

Yeah its Wanneroo so clockwise. Only four serious corners, three right handers - 2 x 180 degree & 1 x 90 & one left hander (90 degrees plus a little). Plus a few less substantial wiggles.

65sec long or short track?!?

if its long track thats not a bad time at all... if its short track you have problems :P

Give me a break (please). :D

It was cold, it was wet, I was tired, out of practice and err, um refer to the driver's book of excuses for further info..

Oh and it was the long track and none of the other AWD's managed to go any quicker on the day. :rofl:

Edited by djr81

Only problem with that is that after a cool down lap, the surface temperature from an infra-red reading isn't the best. By that time, the heat has spread through the tyre and the results aren't 100% accurate. You really need a probe to get the carcass temp at 3 points across the tyre, and even then the cool down lap dilutes the results a bit.

Now if you could get that image as a real-time video, that would be awesome to see. :(

if we are serious and checking tyre temps and pressures there is no cool down lap. warm up lap, on it lap, on it lap, into pits, quick as possible measurements then back out for cool down/warm up lap again. no point wasting 2 minutes wrecking the data toodling around on a cooling lap. :) I'm sure richard did the same.

I assume the pictures are taken from the rear of the tyre and the slow down lap wasn't all that slow.

As Showza posted above skin temperature isn't always a good indicator, you need to get below the surface to get a true view. That said, it's a place to start the thinking.

The LHS tyres look pretty good, reasonably even.

The RHS tyres shows too much camber, as you would expect from a clockwise circuit.

The LHS front maybe needs a little more pressure, maybe 1 lb

Both of the RHS tyres need more pressure, maybe 2 lbs.

At Wannaroo we always run less camber on the RHS than the LHS in an attempt to get more of the load onto the inside tyres. Share the traction around for cornering. Plus it helps under brakes with less camber on the inside tyre. As well as staggered camber we also run staggered tyre pressure (as I mentioned above).

Gotta go, Eastern Creek this weekend and I have lots of cars running.

Cheers

Gary

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...