Jump to content
SAU Community

Recommended Posts

I might have semi's by then too, kinda had a few grip problems.

I would of thought cold semi's would grip less than RE001's? or have they been heat-f**ked? Mine are 40k km old and have been through many a heat cycle in the hills(hot to touch after a drive), Then again, I have never had semi's(havent driven on the KU36's yet)

What pads/rotors/fluid are you running? I find some pads alot harder than others to recover from a lock-up...

  • Replies 358
  • Created
  • Last Reply

Top Posters In This Topic

Heat-f*cked. They've seen 3 or 4 track days (can't remember) and 1.5 DECA's. They've been melted a couple too many times.

And yes, my brakes are shit and need attention. I'm running SSS brakes front and rear, I haven't changed the master cylinder and brake booster and I've got no ABS. My car stock basically has a drum rear end and tiny calipers up front. It now has bigger calipers (still single piston) up front and discs on the rear. Normally I can deal with them being really touchy but at DECA last weekend they just kept locking up. Obviously the last straw was the sweeper on the Long Wang, locked them up and I was gone.

Pads are Bendix Advance front and Nissan OEM rear, Rotors are DBA slotted front and Nissan OEM rear. I noticed today when I drove the car to the panelbeater that the fluid has boiled over. I've obviously cooked it.

So on my to do list is fixing it cosmetically and mechanically (which is what is happening now), and them paying some attention to my brakes and tyres. Should be there for DECA in November, Long Wang will make me a little nervous though.

i didnt see Romans flat spot but he told me about it!! thats when ABS helps!! lol

ima disconnect the ABS next time and see how i go....my semis are re55s but they dont have much tread left so they will be in the bin after November DECA

i didnt see Romans flat spot but he told me about it!! thats when ABS helps!! lol

ima disconnect the ABS next time and see how i go....my semis are re55s but they dont have much tread left so they will be in the bin after November DECA

ha ha yeas ABS does help prevent flat spots, but it cuts in way too much and slows you down. after doing 2 DECAs with ABS i actually like no ABS. The flat spots are mostly coz my tires are shit and only 185s which is smaller than stock.

hopefully I'll have some 17x9s and some federals before November

If I were you guys I would save my money and spend it elsewhere rather than on expensive semi slick tyres hoping that will make you a better driver, fix all your problems and get you faster times.

Semis = faster corner speeds which means lesser margins for error and also = much harder hits when you collide with something.

Most (not all) of the time cheap semis that have gone through a few hard heat cycles, stick worse than street rubber.

Get decent sized street tyres that will last substantially longer than semis, and save on regular fitting and balances, and spend money on the basics; good pads, good fluid, coilovers and or swaybars, and suspension links that will give you better turn in and decent camber (castor/tension and camber rods). Those get you faster times and arent consumables like tyres.

But hey, if you wanna run semi slicks and be cool, then thats ok too, just my 3c.

If I were you guys I would save my money and spend it elsewhere rather than on expensive semi slick tyres hoping that will make you a better driver, fix all your problems and get you faster times.

Semis = faster corner speeds which means lesser margins for error and also = much harder hits when you collide with something.

Most (not all) of the time cheap semis that have gone through a few hard heat cycles, stick worse than street rubber.

Get decent sized street tyres that will last substantially longer than semis, and save on regular fitting and balances, and spend money on the basics; good pads, good fluid, coilovers and or swaybars, and suspension links that will give you better turn in and decent camber (castor/tension and camber rods). Those get you faster times and arent consumables like tyres.

But hey, if you wanna run semi slicks and be cool, then thats ok too, just my 3c.

Wise words :(

Sarah those pics came out awesome!!

7th...i would have thought a $50 to each time keeper would have been enough for 1st...damn global financial bs. maybe $100 next time team??

great day as always from the DECA team. there is alot of keyboard heros in this thread...or is it just me?

well mick and the guys will be hearing from me, hrm tyre wall. HH on saturday is going to be a struggle me thinks.

If I were you guys I would save my money and spend it elsewhere rather than on expensive semi slick tyres hoping that will make you a better driver, fix all your problems and get you faster times.

Semis = faster corner speeds which means lesser margins for error and also = much harder hits when you collide with something.

Most (not all) of the time cheap semis that have gone through a few hard heat cycles, stick worse than street rubber.

Get decent sized street tyres that will last substantially longer than semis, and save on regular fitting and balances, and spend money on the basics; good pads, good fluid, coilovers and or swaybars, and suspension links that will give you better turn in and decent camber (castor/tension and camber rods). Those get you faster times and arent consumables like tyres.

But hey, if you wanna run semi slicks and be cool, then thats ok too, just my 3c.

I've had quite good experiences with used semis. Sure if you get them at 30% they're pretty shagged and slippery but it's not uncommon to find 60%+ tyres for a fraction of the cost new and they will have more grip than all but the most expensive streets. At deca you don't really get them hot but for actual track work, used semis will outlast any street tyre. Street tyres get hot and fall to bits.

Nobody is saying semis will make you a better driver. They will make the same driver go faster and unfortunately that's the game we're in!

agree with femno and al on the street vs semi tyres

nothing wrong with doing it in street tyres

plenty of the guys have and do

the last thing you want to do is come to something like deca

with semi's on and have no idea how its going to handle

I think what femno was relaying was semi's are a thing to buy but just not the first. Improving your cars suspension while improving your driving skills and then once you have hit the limits of street tyres you will definitely be ready for semis. What's the point of putting them on to take corners at 180km/h when you can't even control the car? Much better to spin out at low speed and learn then spin out at high speed with semis and potentially damage things :P

but then again you vic people are odd :(

I've had quite good experiences with used semis. Sure if you get them at 30% they're pretty shagged and slippery but it's not uncommon to find 60%+ tyres for a fraction of the cost new and they will have more grip than all but the most expensive streets. At deca you don't really get them hot but for actual track work, used semis will outlast any street tyre. Street tyres get hot and fall to bits.

Nobody is saying semis will make you a better driver. They will make the same driver go faster and unfortunately that's the game we're in!

If I were you guys I would save my money and spend it elsewhere rather than on expensive semi slick tyres hoping that will make you a better driver, fix all your problems and get you faster times.

Semis = faster corner speeds which means lesser margins for error and also = much harder hits when you collide with something.

Most (not all) of the time cheap semis that have gone through a few hard heat cycles, stick worse than street rubber.

Get decent sized street tyres that will last substantially longer than semis, and save on regular fitting and balances, and spend money on the basics; good pads, good fluid, coilovers and or swaybars, and suspension links that will give you better turn in and decent camber (castor/tension and camber rods). Those get you faster times and arent consumables like tyres.

But hey, if you wanna run semi slicks and be cool, then thats ok too, just my 3c.

Thats what I thought too... and some pad compounds are a lot easier to recover from lockups than others.

If I were you guys I would save my money and spend it elsewhere rather than on expensive semi slick tyres hoping that will make you a better driver, fix all your problems and get you faster times.

Semis = faster corner speeds which means lesser margins for error and also = much harder hits when you collide with something.

Most (not all) of the time cheap semis that have gone through a few hard heat cycles, stick worse than street rubber.

Get decent sized street tyres that will last substantially longer than semis, and save on regular fitting and balances, and spend money on the basics; good pads, good fluid, coilovers and or swaybars, and suspension links that will give you better turn in and decent camber (castor/tension and camber rods). Those get you faster times and arent consumables like tyres.

But hey, if you wanna run semi slicks and be cool, then thats ok too, just my 3c.

I think what femno was relaying was semi's are a thing to buy but just not the first. Improving your cars suspension while improving your driving skills and then once you have hit the limits of street tyres you will definitely be ready for semis. What's the point of putting them on to take corners at 180km/h when you can't even control the car? Much better to spin out at low speed and learn then spin out at high speed with semis and potentially damage things :)

but then again you vic people are odd :thumbsup:

Well said guys.

I am a believer in semis for track but not deca. they are an advantage if they have life in them but a nightmare when they dont (especially on the skid pan). also, cold semis are worse than cold streets, 1 little lock up on the mini wang or the basketball court say hello to way bigger flat spots and canvas if they are low. i normally run semis simply because they are always on the car but i ran streets this time and it was a good reminder that they can teach you things at a still fast but not too fasta speed.

Tubs, i would be bring 3 sets if i was you :)

Just got back from Nissan Datsun Sports Owners Club Vs. FOrd XR club motorkhana and would like to share some ideas which was used in their format.

Their skidpan runs are based on official cams motorkhana circuits

http://cams.com.au/en/Sport/Disciplines/Au...sts%202002.ashx

They split the skidpan in 2, and had 2 seperate skidpan courses on each side (Instead of sauvic having one large skidpan event taking up the whole pan)

The Cams circuits (for example "Happy Birthday" and "World Tour") are small but have plenty of turns in order to do a lot of sideways fun or aim for quick timing. It's also good for the low-powered cars as they dont need huge amounts of power to get from one side of the skidpan to the other.

A couple of goods one are "crossover" and "Straight slalom" etc all small in size but are quite difficult and dont require a lot of power to be quick.

Also at the end of the day, they had a knock out challenge which consisted of slalom up and then back down to the finish line (an idea for future knock outs for sauvic?)

So just throwing out some suggestions for future deca's :thumbsup:

Cheers

interesting read.

i was thinking semi's for november but i'm opting out as even my road tyre's were different cold and hot. Might look into some more suspension work even tho i was very happy with the sliding and steering omg where was my wheel alignment last deca ???? (its soooo much better) but iv'e already spent to much money on my car to just have fun in.

also the question was asked how happy we were with the new format and difficulty which is why i responded. i did watch cars ahead of time and did review the map/layout but minutes in advance. I was able to iron out alot of bugs on the weekend, a problem with only drivin the car on track days.

And if roman wins the type X catagory, i think i win the modified Club Q catagory, lmao how many in the class were there ?

lmao glad i got rid of NA, auto, hicas, abs, 15" tyres and now sunroof

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day  
    • While I was waiting for the new parts to come in for the charge pipe and radiator I decided to do some turbo modification. The drive pressure (exhaust backpressure) was a lot higher that I thought it should be. For 32lbs of boost drive was 55lbs. The turbine housing is a 1.10AR and my turbo builder has suggested to go to a 1.25AR. To test if a larger AR would do anything to reduce drive pressure AND not spend any money I decided to hog out the divider in my current housing. I removed it from the inlet and the whole way through the housing.  After reassembly and testing it doesn't look like this modification did anything for reducing drive pressure or requiring more fuel (making more power). Oh well, it was worth a shot. We'll get some data at the track if it makes it past the 60ft. I also machined a $7 shift knob off Amazon to fit my Stillway shifter since I didn't like the Stillway shift knob. Next on the list was the radiator replacement and fabrication of a new intercooler tube that had no silicon coupler. No pictures of this - I was short on time each night after work to get this done and didn't stop to take pictures.  Next was to get the clutch disks out and replaced. Previously when installing the dogbox I had ordered a set of the same sintered iron disks I had been running because I switched to the 26-spline input shaft. I thought it was odd that they didn't have any markings or brand name on them like all my old disks had but installed them anyway. At the track I could not get the clutch to lock up using my normal strategies. After two track nights I reached out to the clutch manufacturer and ask their thoughts. They said they had to switch the material out because they were having trouble getting the original material and that this new material would not take to being slipped very well.  So out with the first set of 26-spline disks and in with the correct material 26-spline disks. While I had the trans out I added an inspection/service hole. I've wanted one of these for a while. Now I can have a look at things and change the front cover shimming when needed (clutch wear). I hustled and got the clutch change done in a few hours on a Saturday. Hopped in the car and drove home. On the way home I did a 1-3 pull. When shifting from 2nd to 3rd the core plug in the back of the cylinder head popped out and dumped all the coolant. Thankfully I was only 30 seconds from home and coasted it there. Datalog showed nothing unusual and 2.5psi of coolant pressure. That plug has been in there since 1992 but I guess it worked its way out. Pulled the trans AGAIN and replaced the plug, JB welded it in, and made a brace. Also deleted the head drain I had added in during the bearing issue fiasco.  I am currently changing my boost control plumbing to make it cleaner. After that is done I'll make another attempt at getting past the 60.
    • Are you 100% sure this isn't tune related?
    • 140-150 across the board. At this point hoping the grounding harness fixes it. My grounds are all tied to the chassis and none to the battery. For SR and KA that’s never been a problem for me but had a few other guys here and Reddit who told me RB really like a very solid ground setup tied to the battery so going to try that next, I’m stumped if that doesn’t do it. Never had a car have spark and fuel and not fire off before. Only thing I can think is the spark is intermittent/weak because of grounds nothing else really makes sense at this point 
    • I am having close to the same issue. Can you help me with what wire you grounded to get your pump to trigger?
×
×
  • Create New...