Jump to content
SAU Community

Recommended Posts

  • Replies 158
  • Created
  • Last Reply

Top Posters In This Topic

Sounds like this is a common thing with plugs ins.

The computer needs a throttle signal as an input to decide what to do with the diff.

The A-LSD computer probably expects a signal to come to it in a particular way, and if it doesn't come in the correct form, then it faults.

So how should we fix the signal? I've had a mechanic check the wires, and he didn't see any issues... :(

OFENSV - yeah...mine doesn't come on when i first turn on the car...and it goes away if the car is turned off for awhile! The a-lsd light on the dash is not the one that flashes a signal. The flashing signal is on the a-lsd/abs computer in the boot. Don't know how to describe it, but it sits above the battery...you have to lean into the boot and look at the bottom of the computer...there will be a little round light that flashes out a sequence. (mine flashed 7 times slowly, then 5 times fast, indicating a tps prob - i think you need to ask someone what the different sequences mean : )

I definitely think its linked in with the pfc, cause i never had that problem with my stock ecu....

  • 3 months later...

Just chanced to happen on this thread when surfing the forum.

Hope you gels got your problems sorted. I could barely understand much of the discussion. I only bought my car in May 2004, so am still on steep learning curve.

Mine is also an R33 active LSD model, built Feb 1994. I managed to track down an owners handbook in english. Its been helpful for the basics.

It says both activeLSD and slip lights (ABS light as well) come on with the ignition, but go out when engine is started. Slip light also comes on when losing rear traction (eg having fun in the wet, or doughies, or perhaps on ice/snow in Japan). Active LSD light (and ABS light) only comes on when driving if there is a system fault.

My car (now) does it exactly like in the manual. But mine is stock standard. Mucking around with electronic mods seems too scary too me.

Hope this is helpful to some active LSD owners.

cheers :(

Hey I don't have an Active LSD 33 but going back to your original qu Moanie I'm pretty sure that the PowerFC doesn't support the Active LSD - hence the lights coming on when the PowerFC is installed..

Nah. I've recently had a powerfc installed and I don't have any problems with it. My slip light and A-LSD/ABS lights are working fine. Not that I have tested them of course. :angel:

I seem to find that it creates a system fault when you are driving up an uneven driveway and one wheel spins but the other is off the ground? Or on a dyno. It comes up with a system fault. Not quite sure why, but my mechanic said it's fine :rofl:

Moanie/NismoGirl. A Q. if I may? Whats a power fc, or shouldn't I ask?

I used to have an FC holden (1959) in a former incarnation, but you wouldn't call that powerful - by today's standards. And I'm sure it's not the answer to my Q.

Hope you are making progress with problems. I have no further insights, beyond how the lights are supposed to work.

Initially, mine did have a problem. None of the ABS,slip, or active LSD lights ever came on. Under warranty, so dealer had problem for 3 weeks. Turned out it was a broken wire inside a plug somewhere. It was like these systems had been turned off with a switch.

Interesting that both ABS and slip/activeLSD systems both ran thru one wire. Seems to support earlier post that both these systems are run from the one computer??

Gazza49: Before you get flamed for your nOOb question. A PowerFC is a full stand-alone replacement ECU which plugs in where your normal Nissan ECU is which allows you to modify your fuel/ignition maps as well as a few other features, like rev limiter etc.

Obviously if you replace the standard ECU which is supposedly running all these bits and pieces like A-LSD etc, you come up with problems if the new computer (ECU) can't handle it.

You'll notice in my signature that i'm awaiting a PowerFC and this certainly doesn't mean i've got an FC holden on order :)

I've search around, checked all 490 odd pages of the r33 service manual and other sites and google. The diff is the same as the vpec gtr diff. If the problem doesn't occur when you use the stock ecu and it does with the powerfc then it must be something the power fc is doing. Not sure what. The service manaul for the r33 doesnt cover anything on the a-lsd or slip functions, it doesnt even mention them

nissan consult wont prove much help either it doesnt have any a-lsd loopback or realtime tests. Find someone else who has a a-lsd r33 and see if you can swap your "lsd" computer in the boot over as a test, but if that was the problem then youd have the same fault with your stock ecu

no idea

I totally agree!!! With all the trouble shooting we did, that had to be the only explanation!! and i haven't noticed any probs with my lsd.... so i'm trying not to stress too much!! I have an awesome mechanic and tuner... so if there was a problem, they'd have already found it by now!! :mad:

Thanks for everyones input!!!! Its always good to hear it coming from someone else :)

Gazza49: Before you get flamed for your nOOb question. A PowerFC is a full stand-alone replacement ECU which plugs in where your normal Nissan ECU is which allows you to modify your fuel/ignition maps as well as a few other features, like rev limiter etc.

Obviously if you replace the standard ECU which is supposedly running all these bits and pieces like A-LSD etc, you come up with problems if the new computer (ECU) can't handle it.

You'll notice in my signature that i'm awaiting a PowerFC and this certainly doesn't mean i've got an FC holden on order :mad:

What's a nOOb question? But ta for reply anyway.

The FC holden wasn't that bad when I think about it. Mine had a Repco super sports engine (but still a sideplate grey), twin carbs, extractors, 2 inch exhaust, fats (steel wheels), lowered suspension and a top speed of 84 MPH. My mates called it the ROCKET.

Is it to late to change your order?

  • 3 weeks later...

Hi Moanie

I have a series 2 with the slip/a-lsd option on my car also.

i was looking in to getting a PFC, and i did actually pose this question on the forums, as i did think about whether apexi would have thought of adding this option in to the PFC, since only few GTST's came with it (maybe the new model PFC have it???).

the responses i got was that the PFC DIDNT come with the inbuilt function to handle our diff (vspec GTR diff). i didnt end up getting PFC though, as im selling my car now, but if i did, i would have imagined i would of got the same 'problem' as you.

if the diff actually still works though, then you dont have much to worry about..

-Michael

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...