Jump to content
SAU Community

Recommended Posts

Hmm there's alot of thoughts on oils.... I'm no expert but seems like redline is the go if you wanna spend the $ or fuchs. But i've never used either.

Just did an 8ok change and put motul 8100, which seemed to be a recommendation of a few different posts.

Put Nulon trans fluid in as well, but never used the nulon engine oil.

It's australian though, so that's a plus :rant:

Edited by bayslideblue
I'm looking at different oils to use for my car,

need some recommendations, I'm looking at this one NULON

http://www.nulon.com.au/products/Full_Synt...sel_Engine_Oil/

thoughts?

Cheers

I use Motul 300v Chrono (10w40) in the Stagea.

I used the that Nulon 10w40 that you are asking about in my wife's Magna kast service. Seems to be good shit.

the Magna was burning a heap of oil and was very noisy (probably due to the 3L of oil that was left in it after 10,000kms). Put the Nulon in with their tappet treatment, damn quiet now and is great on startup. My wife says that the car is much, much smoother now.

Have had in the Stagea (all 100% Synthetic);

Royal Purple - good.

SHell Helix Ultra - ok.

Mobil 1 5w40 - too thin, engine didn't "feel" together, was quite noisy and I didn't have the confidence to push it.

Castrol Edge - not so good. Engine "felt" loose and was a bit noisier than I would have liked.

Motul 8100 - rubbish, could smell it burning, when I changed it (800kms after putting it in) a large mass of crap that smelt like charcoal came out.

Amsoil 10w40 - good.

Penrite Syn 0w50- way too thick. Felt like the intake pipe was 90% blocked off. Just didn't want to rev. (changed after 1100kms)

Motul 300v Chrono 10w40 - Best to far... by a long way too! Engine revs effortlessly, is damn smooth and is quieter than the any on this list. (too bad it costs so much)

I used to change every 5000kms, but I have extended that to every 10,000kms with the 300v.

Will be trying the Nulon 10w40 with my next service (2000kms away).

I say give it a shot. If it doesn't feel good (you will know), just change it. 5L of Nulon is what, $50?

Oils have different grades. Have a read of the different grades of full synthetic oils. "Full synthetic" is sometimes more of a marketing term than actually 100% synthetic. It may or may not be true.

Basically if I remember correctly, Nulon 300V was one of the few grade 5 oils, most other full synthetics are grade 4 (redline & royal purple i think) which is still pretty good, and then there are also a lot of grade 3 oils, which are still listed as "full synthetic" even though some of them are actually a semi-synthetic. This includes shell helix ultra...unless they've changed it recently...

Either way a synthetic oil will work well, just depends how critical you are. The average joe just sends their car to your average mechanic and their cars usually last the distance...so who knows...

"I use Motul 300v Chrono (10w40) in the Stagea.

I used the that Nulon 10w40 that you are asking about in my wife's Magna kast service. Seems to be good shit.

the Magna was burning a heap of oil and was very noisy (probably due to the 3L of oil that was left in it after 10,000kms). Put the Nulon in with their tappet treatment, damn quiet now and is great on startup. My wife says that the car is much, much smoother now.

Have had in the Stagea (all 100% Synthetic);

Royal Purple - good.

SHell Helix Ultra - ok.

Mobil 1 5w40 - too thin, engine didn't "feel" together, was quite noisy and I didn't have the confidence to push it.

Castrol Edge - not so good. Engine "felt" loose and was a bit noisier than I would have liked."

What grade Castrol Edge were you using? I had been using 5w 30 which was no good for my car but now on 10w 60 it is fine.

It really depends on what sort of climate that you live in.

If you live in cold climates then look for a lower figure with the W after it (5W) means that the oil flows as a 5 weight oil at 0 degC.

If you live in higher temperatures obviously this is less important, so you can go to 10W or even 20W.

The higher number is how the oil perfoms (flows) at 100 degC. So a 5W/40 acts a 5 weight at 0 deg and a 40 weight at 100 deg.

Now obviously you'd like it to run as a 5 weight at 100 deg eh? WRONG.... 5 weight oil at 100 deg is like water! 40 weight oil at 0 deg is like honey. So that's why we want a 5W/40... which is pretty consistent all the way from 0 - 100 deg C.

Keeping an oil in your engine too long will load it with contaminates. Mainly carbon, but also some metals (your engine wear!!). The non-synthetic oils use polymers to boost the viscosity at higher temps.

Imagine them like bits of styrene packaging suspended in the oil. As it get hotter they expand and make the oil thicker. Your engine is mashing them up though all the time.

So eventually they lose the ability to expand and do their job properly. Which is why you need to change them fairly often.

Pure synthetics don't do this.

I used to work for a Shell company. Once Shell did an experiment on a Cummins diesel, they ran it to destruction. It took about 630,000 hours. They didn't change the oil, or filters. They worked out that the replacement cost outweighed the maintenance cost by a staggering $60,000!

I once did an oil test on Mobil 1, for a customer. After 20,000 km, the test came back "This oil is as new".

It did have some contaminants but this was minor. The oil itself had not degraded. Good filters are worth far more than this brand or that brand.

Me I use Castrol Edge 5W/30 at the moment. If money wasn't any object it would be Mobil 1 every time. I'd probably go to 10,000km oil changes then instead of about 5,000km which usually turn into 7,000km oil changes!!

Remember all oils are tested if you don't understand what you are putting in your engine..... go read!! Start by Google-ing Oil Viscosity Chart.

The better you understand the more confident you will be.....

Hope this helped though.

i have castrol edge 10w30 and i know what Cam means when he says it sounds 'loose' and yes its noisier then before!

that said, it revs more smoothly (to me) and hasnt discoloured the oil so it appears to be doing its job.

im also thinking of going down the nulon engine oil path soon

I currently use Martini Racing Oil

Synt http://www.martiniracing.com.au/resources/...tini%20Sint.pdf

Martini is my current aswell! although that WAS my first service just last week.

seems to be running fine if not slightly better than before!, and it had Motul in it before Martini i do beleive. ;)

Synforce ProSYN 730 - 7.5w/30

http://www.synforce.com.au/synthetics.html

Queensland made for nissan motors. Was in my car when i bought it and found it good, currently running Castrol edge 5w/30 and find it poor in comparison...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...