Jump to content
SAU Community

Recommended Posts

I *think* I saw Merli tonight driving down mona vale rd, otherwise it was another midnight purple '33 with Xenons.

Also had a chat to a dude in a g/metal 32 GTR on mona road, same place as Merli except opposite direction and 10hrs earlier! :)

Thanks.  It's very dirty and had the old wheels on it.  Well it might not have had any wheels on it when you saw it as I got some new rotors put on the front and had the back ones skimmed.

 

Was yours the grey one?

No mines the Black R34. You might not have seen it.

Yeah I was told your brakes were squealing.

Later today after school I saw an R31 GTS-2 in the lowest level in the carpark.

Nice bright red paint, looked like 4 stud roh drift R rims with some negative camber. Had full gts-2 body kit, Nismo sticker on the rear window.

i think plates were GTS - 112

Nice car.

Spotted: Servo full of Skylines in St Ives last night, good timing and not a bad cruise either fellas.

ooo!!! was that mintie and crew??? they were heading to palm beach last night!!!

And they started off at homebush!! but i don't remember seeing a yellow 34... so maybe that was another group....

Saw a nice white '33 today driving down mona vale rd at about 2pm - i flashed and got a flash back, female asian looking driver.

Also saw a wine red '33 on Mona vale rd about the same time.

Seen a black r32 gts-t twice today. had a GTR front bar and grill ( could have been a GTR ).

First time was on Old Bathurst RD, he was heading towards penrith.

Second time was when we were coming home from Emu plains, he was at the Mulgoa Rd lights waiting to get onto the M4 with what looked like his friend in a WRX behind him.

JB - 159

purple R33 GTR, plate GTR-028 spotted on Victoria avenue chatswood. Nice GTR, with big FMIC and nive 5 Zigen wheels. Had a big SAU sticker accross the windscreen too :(

Richard

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi. This is just my curiosity because iam sure the tuner figure something out...but either way i want to ask. The "problem" is that the Nistune ECU (Stagea FW and RB25DET NEO from Stagea) sees many times the speed than the speedo does(he says the speedo show 120 km/h - correct speed and the ECU shows like 510km/h ) I told him that this car/tranny getting speed from rear diff. If iam not mistaken the RB25DET NEO "need" to see tranny speed sensor? (my tranny has the plug for it). So couple of "question" If he connects/wire the speed sensor to the tranny...are the signals gonna intervene and if...what if he disconnects the rear diff one and the speedo stops working? Or the "new" sensor from the tranny "take over" and will not going need the one from diff? As i said i know he figure/get that done...iam just curious to know what are the solutions 🙂 
    • Your IACV is set to idle too low. You need to adjust it via the screw Duncan mentioned. From memory it should be 650rpm with the valve electrics unplugged. What is it trying to idle at with the IACV plugged in?
    • Ahhh, I need the whole head unit. I definitely needed to roll back through and review your setup, ha ha! Neat setup they have going on. I just need a full double din head unit. But I want good and responsive. I might have to review what the likes of pioneer have out these days.
    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
×
×
  • Create New...